Forum Replies Created
-
AuthorPosts
-
electrofix
Moderatorput a new plug on it and possibly the socket and it will be fine
Dave
electrofix
Moderatorlooks like the replacement is rubber
look here. there are 2 different commercial codes but they have the same seal as far as I can see
Gasket Oven Door Std Materia J00814871 – Indesit Spare PartsDave
electrofix
Moderatorthe drum on this model is electrically split front and rear
there is a brush in the rear by the rear bearing and another running on the front of the drum. check the one at the front is making good contact as well as the one at the rear.
also check the front and rear of the drums are electrically isolatedDave
electrofix
Moderatoryou have posted in the public forums so i have to be careful what i say
have sent you the manual
Dave
November 19, 2022 at 2:42 pm in reply to: Neff dishwasher E09 code, replaced Heat Pump now water not heating #484501electrofix
Moderatorthe large connections on the side of the motor
one connection is earth the other 2 are the heater and will have a low resistance (under 100 ohm). Look at the connector on the unit you will see which is which
Dave
electrofix
Moderatorit would be nice for Ebac to be able to see the above and comment as if its true its would be terrible customer service
I would also have tried to get some sort of payment to cover damaged clothes at least since the first visit
its not that I dont believe whats happend but I have no way to verify so I have to try to be neutral
Dave
November 19, 2022 at 2:23 pm in reply to: Neff dishwasher E09 code, replaced Heat Pump now water not heating #484498electrofix
Moderatorhave asked Kenn above to check as youi can see above so see what he comes back with
check the side connections on the motor they are the heater and thermostat connections
ok in the meantime did you check the old heater to see if its faulty as all E09 seems to mean is a heating fault but does not narrow down the component
Dave
November 19, 2022 at 12:45 pm in reply to: Neff dishwasher E09 code, replaced Heat Pump now water not heating #484496electrofix
Moderatorok
I need it of the sticker on the doorafter the number it will be one of the following
/1 /2 /3 /4 /6 /7 /10 /13 /14 or /18
chances are its pump 651956
who is the supplier of the part as all of my wholesalers do not have an alternative pump for this number. They do have an alternative for 12019637 but not for 651956
https://shop.ukwhitegoods.co.uk/6519…sher-heat-pump does not have an alterantive
https://shop.ukwhitegoods.co.uk/1201…sher-heat-pump does have an alternative
they may look the same but may be electrically different
Dave
[USER=”2″]kwatt[/USER]
have you any info to confirm or deny 651956 its interchangeable with 12019637 because i would say noNovember 19, 2022 at 12:07 pm in reply to: Neff dishwasher E09 code, replaced Heat Pump now water not heating #484494electrofix
Moderatorok first we need to check you have the correct pump
your Enr is stated as S51M53X1GB but i need the last 2 digits after the /
what pump did you purchase to replace the installed one ?
Dave
November 18, 2022 at 10:28 pm in reply to: Miele wda 210 washing machine, Type HW07, NR64 /118655731 #484491electrofix
Moderatorthey tell you the sizes on the miele website
6305 and 6306
Dave
electrofix
Moderatoryou wont know till you try
i agree it does look similar but the shaft may be longer or shorter causing the fan to catch
did check all 3 models of this oven and all use the same motor
https://www.bosch-home.co.uk/supportdetail/product/HBN430520B/03#/Tabs=section-spareparts/
Dave
electrofix
Moderatorget a really silly proce for the motor
https://shop.ukwhitegoods.co.uk/490541-fan-oven-motor
just remove the rear cover and check the fan has not come loose for any reason
Dave
November 17, 2022 at 10:46 pm in reply to: Zanussi ZBB28651SA integrated fridge freezer too cold – where is the thermistor??? #484430electrofix
Moderatorneeds to be checked but this kit is probably what you need
https://shop.ukwhitegoods.co.uk/50292181000-air-sensor-repair-kit
you basically drill a hole to find cable and joint a new sensor in
some of the instructions below
Dave
electrofix
Moderatordeltra wrote:how about flow sensor?(impellor jug) it measures incoming supply.
only if the light is not flashing as thats the fill error signal. if its flashing it could almost be anything else
Dave
electrofix
Moderatorwell connect have their problems and going through financial turmoil
low stock levels if stock at all on some lines, plus to me they are way too dear on most things means i only use if i have to. A lot of the time their ebay site (wow discounts) is cheaper than trade
if you have not tried Aswo its time to look
Dave
-
AuthorPosts
