helo_75

Forum Replies Created

Viewing 15 posts - 1,771 through 1,785 (of 4,174 total)
  • Author
    Posts
  • in reply to: Neff U1721 does it need a oven housing #272667
    helo_75
    Participant

    originally, the neff oven would have been supplied with 2 brackets, which sat either side of the unit, and the oven sat on them

    its as simple as even making batons on either side of the units for it to sit on… even on legs if u wanna splash the cash
    either way, ull still need to secure the oven to the unit by whatever holes/fittings available

    in reply to: hotpoint Tumble Dryer #272641
    helo_75
    Participant

    you need to check the drain hole behind the pump isnt blocked

    if you take the pump unit out, youll find a small drain hole at the bottom left of the grey plastic housing…. i push an old broken tumble dryer belt through and pull it out through the condenser housing to make sure the restriction doesnt flow back through

    if it doesnt drain properly, it fills up in the fan chamber, then sprays water over the heater

    in reply to: Where is he? #271949
    helo_75
    Participant

    hes back on about his dishwasher, im so adamant im not going to his house, ive took the day off as a holiday

    at best, hes difficult

    i worry what depths he might sink to to get what he requires? write offs and exchanges are as rare at comet as a spinning haier, and he’ll only take so much

    u guys are lucky, you dont have to deal with him, i just hope he never gets hold of a manager and makes reference to my posts on here?

    in reply to: Hoover TV630 #272548
    helo_75
    Participant

    check the wires are plugged in properly, its easy to get them wrong, or not in properly

    in reply to: leaking hoover pfa 137 #272535
    helo_75
    Participant

    theres a hose from the underside of the soap box, leading to the top of the pump, it will have rubbed a hole in it

    DO NOT use it again until the hose is repaired/replaced, as it will damage the pcb

    in reply to: Zanussi Dce 5655 Dishwasher Not heating. Very long Cycle ?? #272515
    helo_75
    Participant

    yup

    id look a little closer at the relay contacts, follow the tracks back

    in reply to: Where is he? #271941
    helo_75
    Participant

    pmsl, he probs dont bother here cos he knows we dont listen to him

    what forums this then 😛

    in reply to: Beko FSA716 F/F Stat Wiring #272528
    helo_75
    Participant

    giz yer email addy , ill send u the info

    in reply to: Where is he? #271939
    helo_75
    Participant

    and, erm, how did you come across this information?

    in reply to: Zanussi Dce 5655 Dishwasher Not heating. Very long Cycle ?? #272513
    helo_75
    Participant

    test the heater with a meter, if thats ok, its the pcb!

    in reply to: Where is he? #271937
    helo_75
    Participant

    is that true?

    cos his wife was askin me about the watchdog thing

    in reply to: Where is he? #271935
    helo_75
    Participant

    hes been back on

    im not goin back, the guys an A grade pr1ck

    wants replacement already, not fit for purpose etc etc

    in reply to: Indesit WD12SUK bearings – how to replace… #272350
    helo_75
    Participant

    nah the seals just a push fit

    like penguin says, just whack it out, its the only way

    in reply to: zanussi zhq575w – oven heating extreemly slow #272442
    helo_75
    Participant

    did it eventually get to temp?
    cos if it did, theres a good chance the fan motor itself is running slow

    in reply to: Creda TCR2 very noisy #272440
    helo_75
    Participant

    http://shop.ukwhitegoods.co.uk/Tumble+D … t+Kit.html

    contais everything you need to put your dryer right, although the drum needs to come out, right hand side panel off, and it becomes obvious

Viewing 15 posts - 1,771 through 1,785 (of 4,174 total)