[helo_75]

i use a good quality, long extension bar, and whack em out with a hammer.. just be carefull

[helo_75]

the inner drum needs to come out.
to avoid damaging the thread of the drum, use a suitable bolt, similar to the pulley bolt, and tighten it up until the threads are taken up.

then bash it out with a big hammer

the bearings, and yes theyre bad, will come out then, you can bash the rear one out from the inside using a suitable drift, the inner bearing wll then knock out from the back

try and use something to draw the bearings in , or theyll end up noisey.. and make sure the shaft of the drum is in good order, or it may need replacing

[helo_75]

3-4 hrs?

an hr, tops

[helo_75]

97922819 is the complete pump, with filter

91941772 is listed as the filter housing with cartridge

[helo_75]

brilliant.. thanks for taking the time to feedback to us

[helo_75]

by pass the board so the fan will work?

yep and freeze everything in the fridge

that is of course if hes right… blocked system me thinks

[helo_75]

There have been 3 versions of Demo Mode used on these appliances:
Version 1 (Production – Date Code 39 March 2005)
To Activate
1. From the default screen of a programme after switching the appliance on press both ‘Start /
Cancel’ and ‘On / Off’ buttons together until ‘d ON’ appears in display.
2. Press the ‘Start / Cancel’ button only and ‘t ES t’ appears in the screen. (Temp and Spin
symbols also appear.)
To Deactivate
Press the ‘Start / Cancel’ button until ALL the console LEDs illuminate.
Press both ‘Start / Cancel’ and ‘On / Off’ buttons together until ‘d OFF’ appears.
The default screen returns and you can select a new programme.
Note: – The default screen information displayed on these models is that of the programme
currently selected by the selector knob.

Version 2 (during Date Code 39 March 2005 – to Date Code 42 June 2005)
To Activate
1. Same method as Version 1.
To Deactivate
1. Simply press the cancel button and the appliance returns to default

Version 3 (During Date Code 43 July 2005 – to date)
To Activate
1. Press ‘On / Off’ and ‘Start / Cancel’ together with the top left option button until ‘d On’
appears. To start the sequence press another function button.
To Deactivate
1. The demo (tESt) mode must be halted before it can be reset.
To do this press and hold ‘Start / Cancel’ for a few seconds until the display illuminates ALL
symbols and a bleep is heard.
2. Press ‘On / Off’ and ‘Start / Cancel’ together with the top left option button until ‘d oFF’
appears.

[helo_75]

they all have them

no heats unlikely to be the module, the timed dry could be..

[helo_75]

Re: New way to replace Bosch brushes.

Martin wrote:

leavemetogetonwithit wrote:
and let us know if this is how you do it. 😆

This is how Penguin45 does it.:wink:

This is how Joe Public does it. 😆

well, you can see in all its glory how bad a repair guy he is

the awfull clicking as the drum starts to turn, cos the brushes are in the wrong way, good job he stopped filming before it blew up!

a little knowledge is definately dangerous

[helo_75]

its got a blocked system

when will u read what people have said?

[helo_75]

check the wire, it could be broken

it could also be the cut out, theyre situated just over the heater

experience would suggest a damaged wire

[helo_75]

nah theyre just crap

unless your good at soldering surface mount led’s on a wafer thin board?

[helo_75]

i still think itll just be the pump

[helo_75]

oh, and ill tell you why before you come at me with ‘it runs ok off the machine’

it will drop off after a minute cos the machine ‘fails to activate the pump’

yes they are that clever, they know the pumps not there

[helo_75]

ouch

yep, its common, thats why theyre £80

[Author]

Posts