helo_75

Forum Replies Created

Viewing 15 posts - 1,366 through 1,380 (of 4,174 total)
1 2 3 … 91 92 93 … 277 278 279
  • Author
    Posts
  • May 1, 2009 at 8:31 pm in reply to: module for Hotpoint WML540? #285533
    helo_75
    Participant

    and that machines quite new… is it 12 months old yet?

    and what is actually wrong with it?

    May 1, 2009 at 8:28 pm in reply to: module for Hotpoint WML540? #285532
    helo_75
    Participant

    thing is youll also need a smart card , and a card reader to programme it

    be easier to contact tony at emw… sent out to you all programmed and ready to fit, fast delivery too

    takes away a lot of hassles, trust me

    http://www.emwelec.co.uk/

    April 29, 2009 at 3:27 pm in reply to: BEKO F/F CDA543FW #285250
    helo_75
    Participant

    id skip it and invest in something of better quality

    April 29, 2009 at 12:58 pm in reply to: Hotpoint WML 520 Leaking Occasionally #285325
    helo_75
    Participant

    i had onre of these just the other day doing that
    there was a sock stuck in the drum, where the fill hose fitted to the drum… it may be worth checking it out

    April 28, 2009 at 10:15 pm in reply to: whirlpool live case #285280
    helo_75
    Participant

    more likeley no earth in the socket?

    u need to unplug it and get an electrician in asap

    April 28, 2009 at 8:01 pm in reply to: BEKO F/F CDA543FW #285248
    helo_75
    Participant

    classic compressor symptoms imafraid

    dont be surprised if it knackered

    April 28, 2009 at 4:19 pm in reply to: BEKO WMA510W – making loud noises #285237
    helo_75
    Participant

    woah there!!!

    id be tipping it back and making sure the bottom weights secure first

    April 28, 2009 at 4:09 pm in reply to: Hotpoint washing machine WF000 #285012
    helo_75
    Participant

    erm, it was the buttons sticking if you want to be factual

    ive done hundreds

    April 27, 2009 at 6:04 pm in reply to: Hoover Tumble Dryer HDC7FME #285084
    helo_75
    Participant

    ahh thatll be the one with the valve undernath that gets clogged full of fluff then?

    April 27, 2009 at 5:13 pm in reply to: hotpoint ff #285059
    helo_75
    Participant

    have you checked the themistor? fan wont switch on until evap hits temperature

    April 27, 2009 at 12:46 pm in reply to: Dyson washing machines #284995
    helo_75
    Participant

    actually, they werent a bad machine

    i had the misfortune to change a tub once, never again

    why they put 3 motors on, ill never know

    the bearings were supposed to be made by ferrari, they should have lasted !

    April 26, 2009 at 10:48 pm in reply to: Hotpoint washing machine WF000 #285005
    helo_75
    Participant

    Re: Hotpoint washing machine WF000

    iadom wrote:Had several, always been the power board. ❓ ❓

    only he said emw checked it

    anyway, the two buttons on the bezel will be sticking
    check machine function with front pcb off machine

    April 22, 2009 at 9:10 pm in reply to: Dismantling a Hotpoint FEW 12 #283715
    helo_75
    Participant

    dont kid yourself gandh1

    hotpoint engineers now fit bearing kits, and need special permission to order even tub rear halves

    April 20, 2009 at 4:38 pm in reply to: indesit w103 #283667
    helo_75
    Participant

    your pumps blocked
    the filter is under the kick strip at the front

    April 19, 2009 at 7:34 pm in reply to: hpt wd420p #283593
    helo_75
    Participant

    had one just yesterday, was the pcb

    and your is probably same

  • Author
    Posts
Viewing 15 posts - 1,366 through 1,380 (of 4,174 total)
1 2 3 … 91 92 93 … 277 278 279