hilly

Forum Replies Created

Viewing 15 posts - 211 through 225 (of 287 total)
  • Author
    Posts
  • in reply to: d/w detergent in salt pot!!!!!!!! #217520
    hilly
    Participant

    Re: d/w detergent in salt pot!!!!!!!!

    thanks for all replies i went today expecting to see it up to the brim with detergent n was fearing the worst but all i found was about a inch in the bottom of the pot so i removed all the water with a large syringe then kept filling it up with warm water and removing it again i repeated this until water was running clear again .

    thanks again paul

    in reply to: d/w detergent in salt pot!!!!!!!! #217517
    hilly
    Participant

    Re: d/w detergent in salt pot!!!!!!!!

    I’ll give it a go Thanks alot

    paul

    in reply to: white knight t/d #217098
    hilly
    Participant

    Re: white knight t/d

    thanks for replies i will double check and clean everything and it is on a outside wall.

    thanks again paul

    in reply to: The strangest thing you can find in a blocked pump #217103
    hilly
    Participant

    Re: The strangest thing you can find in a blocked pump

    ive removed a nicotine patch from a hotpoint, and the good old cash 😀 £7.46 from the sump of a hoover w/m

    paul

    in reply to: bosch d/w sgs5302gb/07 #215520
    hilly
    Participant

    Re: bosch d/w sgs5302gb/07

    customer rang since i poked around in the machine the other day its been ok, went back today and resoldered the relay just incase so fingers crossed!!!!

    thanks for the replies,,paul

    in reply to: bosch d/w sgs5302gb/07 #215519
    hilly
    Participant

    Re: bosch d/w sgs5302gb/07

    cheers i did solder relay on pcb about 4 months ago still looks ok but i will re do it just incase

    cheers paul

    in reply to: bosch d/w sgs5302gb/07 #215516
    hilly
    Participant

    Re: bosch d/w sgs5302gb/07

    cheers chris, its all clear in there?


    paul

    in reply to: indesit widl126s #213856
    hilly
    Participant

    Re: indesit widl126s

    it was module at fault. got it repaired at emw all ok now 😀

    in reply to: widl126s indesit #214463
    hilly
    Participant

    Re: widl126s indesit

    cheers jim will give it a go

    in reply to: SIEMENS WM5487AGB/04 #212476
    hilly
    Participant

    Re: SIEMENS WM5487AGB/04

    going back tomorrow to check ive not missed anything cos pcb quite pricey any more ideas b4 i go?


    paul 😕

    in reply to: SIEMENS WM5487AGB/04 #212475
    hilly
    Participant

    Re: SIEMENS WM5487AGB/04

    yes sorry martin heater tests ok.

    paul

    in reply to: Bosch won’t take conditioner #211293
    hilly
    Participant

    Re: Bosch won’t take conditioner

    i come across this quite often just remove top of dispenser then you can split the top half in two and just clean the crud away with a brush nice quick job n good as new when done (i use a putty knife to pop the top half apart)

    hope this helps, paul

    in reply to: gen dom bf41 #211553
    hilly
    Participant

    Re: gen dom bf41

    yep heater in plastic sump at the front rhs looks like a zan nexus heater.
    any idea of part no or best place to get one, might as well try one in

    ta paul

    in reply to: gen dom bf41 #211551
    hilly
    Participant

    Re: gen dom bf41

    yeah that was my first thaught but heater tests fine first time ive seen this one its got a strange circ pump on it (similar to whirlpool askol type)

    paul

    in reply to: hyundai dw13? #208970
    hilly
    Participant

    Re: hyundai dw13?

    stat is about two thirds back on right hand side. but dont worry customer rang today hes going to invest in a new d/w (not a import this time)
    thanks for replies 😀

    cheers paul

Viewing 15 posts - 211 through 225 (of 287 total)