Forum Replies Created
-
Posts
-
Re: Hotpoint WMF520 P total loss of power help please
definately worth getting repaired owing to the fact its been moved there’s a good possibility one of the multi plugs may have been tugged off the pcb….
Re: hotpoint wd420
sounds like the wee transistor on the pcb may have blown so not carrying the load. If you look on the top left hand side of the board there’s a wee group of 4 of them I think they control the valves and the pump component numbers Q10, Q11, Q12 AND Q13 .I cant remember which is which but the location of the pump feed wires will show you
Re: Washing machine fires
the only one i’ve ever seen was in the hotpoint training school which they had ” removed for investigation ” pdq I’d have thought. It was one of the economy inde’s with the green decals. The soap box breather was squirting into the power module behind the control panel…funnily enough never heard any more about that fault….
Re: Hoover Nextra HNC170 wiring diagram/service manual neede
I guess A1’s kinda busy, and I’ve no problem with that. Could anyone else possibly help me out with a manual for this?
Re: Hoover Nextra HNC170 wiring diagram/service manual neede
Alrighty mate ! thanks for the speedy reply. I tried emailing you but I know you’ll be busy ! Wouldn’t press you at all but I’ve got the eejit breathing down my neck looking for a resolution. Pop off a copy when you get the chance, Thanks
Re: Bosch, Neff, Siemens Showing 1 min left syndrome
thanks for the info had one in my area with this for a while but since it doesnt seem to effect performance i’ve just let sleeping dogs lie
Re: "UNIVERSAL COOKER"
Never heard of them myself but try this link there’s a ” contact us ” button which might point you to a spares supplier
Re: John Lewis JLWM1407…E52
Could be a dry joint on either one of the motor relays or the triac on the pcb Jim or possibly a wire going into the motor plug on the verge of breaking but still making contact till shaken by spin, give all the motor plug wires a wee tug, have found them come adrift a few times. As far as I can remember the sole motor had a one hit fuse on the stator so it wouldnt reset itself.
Re: John Lewis JLWM1203 Washing machine No Spin/wash
theres a possibility of the motor being heavily carboned causing a weak field to be generated as the insulation between armature segments is being greatly reduced by the conductive carbon dust.If the motor turns empty I would say its far more likely to be a motor fault than a PCB fault.
Re: Hotpoint TCD970P Wiring diagram required
Many thanks to iadom however the customer had blew the bottom off the pcb trying to fit the wrong element so unless i can dig up a working used power pcb its scrap.
Re: Hygena Dishwasher model ahy 8122 not fillinf with water.
try resetting the aqua lock on the fill valve by…turning off the water going to the dishwasher, screw off the hose at the dishwasher side, turn on the machine and set to a wash cycle, wait till you here the valve buzz which means its energized and open, wait a couple of mins with the power on which will allow the aqua stop to drain out the valve. turn power off. reconnect water hose, put dishwasher back on to a wash cycle , again wait till you you hear the valve buzz at which point gradually open the water supply tap to the dishwasher and you should hear it fill.
Re: Hotpoint WDD960 being fixed
there’s a good chance given its age it’s a sealed or welded tub as they’re known in which case its a single unit replacement full tub outer and inner front back the lot comes in one piece and simply replaced. As its hotpoint your getting the engineers carry a whack of parts and its highly unlikely they’ll BER it as repairing it is almost always cheaper. I went to one while working for hotpoint the tub had jumped its mount smashed the door and caved in the side of the cabinet, they still told me to order all the bits and rebuild it…..
Re: Zanussi Electrolux 1500 Aquacycle 5Kg Problem
The belt coming off would suggest either drum bearing wear causing the pulley to ” wobble” throwing off the belt or alternativly the main pcb has developed a fault causing the motor to surge and slip off the belt due to the fact your pcb seems to now be in error mode it would suggest this is more likely . On this occasion I would recommend you call an engineer to have a look and access the machines on board diagnostic in order to narrow down the fault, it might cost you a min charge call out but save you a lot of heartache in the long run…. sorry its not an easy one….
