kaibart

Forum Replies Created

Viewing 15 posts - 901 through 915 (of 1,334 total)
1 2 3 … 60 61 62 … 87 88 89
  • Author
    Posts
  • January 25, 2018 at 7:03 pm in reply to: curry’s essentials cdw60s14 heater #453376
    kaibart
    Moderator

    Re: curry’s essentials cdw60s14 heater

    I’m sure the beko flow throw heater will fit

    January 23, 2018 at 8:01 pm in reply to: Work required – midlands #443331
    kaibart
    Moderator

    Re: Work required – midlands

    Beko are recruiting via agency’s contact concept recruitment and ask for Lucy or Woodrow mercer and ask for Chantel this is direct with manufacture so you do get training

    January 23, 2018 at 7:56 pm in reply to: LG F1403FD Pump #453318
    kaibart
    Moderator

    Re: LG F1403FD Pump

    Ok just use the pump housing and old pump wiring remove the pumps but pay attention to what position they are in,the pump housing is fine,you could have gone to the site shop and just replace the pumps alone. Doesn’t matter about the wattage or amps written on the pumps

    January 23, 2018 at 12:47 pm in reply to: LG F1403FD Pump #453316
    kaibart
    Moderator

    Re: LG F1403FD Pump

    Just use the existing wiring on old pump

    January 21, 2018 at 5:44 pm in reply to: lamona HJA8630 dishwasher #453266
    kaibart
    Moderator

    Re: lamona HJA8630 dishwasher

    Have you checked the spray arms?

    January 17, 2018 at 9:04 pm in reply to: LG Washer Dryer F1403RD6 #444555
    kaibart
    Moderator

    Re: LG Washer Dryer F1403RD6

    Yes the contacts on them I’ve had problems with

    January 17, 2018 at 7:08 am in reply to: LG Washer Dryer F1403RD6 #444553
    kaibart
    Moderator

    Re: LG Washer Dryer F1403RD6

    Check ribbon cable going to display board can give the fault

    January 17, 2018 at 7:06 am in reply to: Indesit IWB6123 #453180
    kaibart
    Moderator

    Re: Indesit IWB6123

    Board fault emw repairs I’ve had in the past had given me so much bother I don’t use them anymore

    January 13, 2018 at 7:08 pm in reply to: Hoover tumble dryer, control module #453018
    kaibart
    Moderator

    Re: Hoover tumble dryer, control module

    More than likely

    January 10, 2018 at 8:20 pm in reply to: Beko WM74125W Element #452934
    kaibart
    Moderator

    Re: Beko WM74125W Element

    This element is in stock with connect both original and pattern they have given you wrong part number I think

    January 10, 2018 at 8:14 pm in reply to: HPT W/D BHWD129 Had Module Fixed But…See Image #452946
    kaibart
    Moderator

    Re: HPT W/D BHWD129 Had Module Fixed But…See Image

    I mean emw

    January 10, 2018 at 8:13 pm in reply to: HPT W/D BHWD129 Had Module Fixed But…See Image #452945
    kaibart
    Moderator

    Re: HPT W/D BHWD129 Had Module Fixed But…See Image

    Faulty module had loads from new that’s why I don’t use them anymore

    January 10, 2018 at 7:44 am in reply to: Hoover dyn 8164 all leds on door locked #452919
    kaibart
    Moderator

    Re: Hoover dyn 8164 all leds on door locked

    2 possible causes facia pcb or main pcb have you checked the rectifier board they blow and give odd faults to my bet would be top pcb thou. Kai

    January 8, 2018 at 8:04 pm in reply to: Lamona (Hoover) W/D HJA8703 Dryer stats #452881
    kaibart
    Moderator

    Re: Lamona (Hoover) W/D HJA8703 Dryer stats

    Your correct Dave more than likely a blockage in the condenser or the fan blade will be full of fluff never changed these stats 9 out of 10 tens it’s a blockage

    January 5, 2018 at 8:24 pm in reply to: Whirlpool #452792
    kaibart
    Moderator

    Re: Whirlpool

    I think they are after d&g work for the cheap end machines from what I heard

  • Author
    Posts
Viewing 15 posts - 901 through 915 (of 1,334 total)
1 2 3 … 60 61 62 … 87 88 89