lerch

Forum Replies Created

Viewing 15 posts - 286 through 300 (of 353 total)
  • Author
    Posts
  • in reply to: hotpoint ctd00p #243779
    lerch
    Participant

    Re: hotpoint ctd00p

    As helo says it cannot have been put back together correctly as there is no other reason.

    in reply to: CREDA T/D TVR 2 #243637
    lerch
    Participant

    Re: CREDA T/D TVR 2

    Have you checked the large relay at the front ???

    part number 1702923 🙂

    in reply to: zanussi zwf1632w #243517
    lerch
    Participant

    Re: zanussi zwf1632w

    Sorry bad news zanussi have only produced enough welded drums for sales not repairs. So you need both parts of the drum, inner drum, heater, heater bracket and 17 bolts. 🙁 not really a viable repair.

    Check around the edge of the drum usually item gets stuck there. 😀

    in reply to: whirpool ADG642 #243535
    lerch
    Participant

    Re: whirpool ADG642

    11 flashes is :-

    FA WI failure.

    If the electronic signal of the flow meter has been received for 3.4ltrs of water on permanent wash system and the WI signal “Water in sump” is missing then an failure is recorded.

    in reply to: ARE QUALTEX SHOPS TRADE ONLY #243513
    lerch
    Participant

    Re: ARE QUALTEX SHOPS TRADE ONLY

    In the past I used CDS based in birmingham, coventry and wolverhampton which have now been purchased by qualtex.

    They did sell to the public at coventry through a shop and sometimes at birmingham on the trade counter but at retail prices and would not give out any trade info. also the rule was “sorry not refunds” get someone in that knows what they are doing. lol 😀

    So I guess qualtex would do the same but at retail prices not trade.

    in reply to: Bosch Tumble dryer #243364
    lerch
    Participant

    Re: Bosch Tumble dryer

    Is it the bosch / white knight dryer wtl6003 if so change both the rear stats in case one has gone weak and tripping at a lower temp.

    in reply to: Bosch WFE2021 prog fault #243263
    lerch
    Participant

    Re: Bosch WFE2021 prog fault

    Alot of the bosch appliances do a quick self test when they first switch on and I have had quite a few where the ntc can cause this fault as well as the motor. Worth checking both if this is one that uses self test. Also as Martin says check the pcb as most of the time you can repair. 😯

    in reply to: Computer nerd required #243161
    lerch
    Participant

    Re: Computer nerd required

    Hi my brother got a computer from mesh about 18 months never had a single day of problems. Good value and not to much preload rubbish.

    He uses his for computer programming using linux and windows xp pro but will not use vista as there are alot of compat. problems with other software.

    hope this helps. 😀

    in reply to: Do you/Don’t you – kids only in the property. #243241
    lerch
    Participant

    Re: Do you/Don’t you – kids only in the property.

    I work for a large well known company and our policy is do not enter if child looks under 16 or if you cannot confirm there age. Not worth the hassle that can sometimes arise. 🙂

    in reply to: w/pool 858674001020 #243229
    lerch
    Participant

    Re: w/pool 858674001020

    Generally the baffle sticks and normally you can just change baffle and will be ok.

    baffle part no. 4812 445 28009

    😀

    in reply to: Hotpoint WMA Door Seal Clamp #243115
    lerch
    Participant

    Re: Hotpoint WMA Door Seal Clamp

    All above good ideas but personally never had any problems usually 15-20 minutes in out and tested. I use small flat blade to unclip and long nose pilers to tighten up 😀

    in reply to: Indesit WIL103 – water valve leakage #243094
    lerch
    Participant

    Re: Indesit WIL103 – water valve leakage

    Never had any problems just changed valves and used old seals. 🙂

    in reply to: LG WM1485FHD programme help. #242805
    lerch
    Participant

    Re: LG WM1485FHD programme help.

    thanks r600a you learn something new everyday. 😀

    in reply to: LG WM1485FHD programme help. #242803
    lerch
    Participant

    Re: LG WM1485FHD programme help.

    Sorry never realised you wanted to do spin only.

    Alf_uckem is correct but not all lg can select spin only on some you have to do rinse and spin @ 19mins pain really. 😀

    in reply to: LG WM1485FHD programme help. #242800
    lerch
    Participant

    Re: LG WM1485FHD programme help.

    You cannot change program without cancelling it – just switch it off and re-select. 😀

Viewing 15 posts - 286 through 300 (of 353 total)