lerch

Forum Replies Created

Viewing 15 posts - 106 through 120 (of 353 total)
  • Author
    Posts
  • in reply to: Samsung RS21DLMR #280128
    lerch
    Participant

    Re: Samsung RS21DLMR

    LOL I was very tired so just paste and cut. 😀

    in reply to: Hoover HNL71463D #280053
    lerch
    Participant

    Re: Hoover HNL71463D

    No but put it into test mode then count the flashes for the error. 😀

    in reply to: Whirlpool American S20D 8586 158 15000 #279828
    lerch
    Participant

    Re: Whirlpool American S20D 8586 158 15000

    It is normally the ice maker itself have done more than I care to remember and has been ice maker every time but once when it was the valve. The sensor go’s faulty and thinks it is full off ice so will not refill.

    in reply to: bOSCH WFL2067gb/16 #280038
    lerch
    Participant

    Re: bOSCH WFL2067gb/16

    Also check ntc as some bosch do a self check upon starting.

    in reply to: Samsung RS21DLMR #280126
    lerch
    Participant

    Re: Samsung RS21DLMR

    I/M sensor connector missing, contact failure, electric wire cut, short-circuit, I/Msensor failure.

    in reply to: Candy CIC 324 AK Fridge Freezer. #280090
    lerch
    Participant

    Re: Candy CIC 324 AK Fridge Freezer.

    Sounds like it could be wired wrong ?

    in reply to: hotpoint ctd00 heat fault ?? #279904
    lerch
    Participant

    Re: hotpoint ctd00 heat fault ??

    use a temp probe and check the temp on half heat and full heat. Approx 60c on 1/2 and about 100c on full. 😀

    in reply to: Credit Theft UK ??? #280142
    lerch
    Participant

    Re: Credit Theft UK ???

    http://www.experian.co.uk/creditreporttv/?sc=410006

    Use these much safer and more well know. Even do a telly advert and on radio.

    in reply to: Beko WMA1512S No drain no Spin?? #250426
    lerch
    Participant

    Re: Beko WMA1512S No drain no Spin??

    The cogs sometimes break inside if customers turns dial a bit quick / rough. Also check dial is linning up correctly as they can wear.

    in reply to: LG wm1437 #278864
    lerch
    Participant

    Re: LG wm1437

    If it is the steam version they have a major problem with the steam generator but will not say so. Everyone I have been to (6-10 units) has had the same fault water in base only after using the steam gen. Leaks along the seal normally and you have to replace the whole unit. Otherwise very good. 😕

    in reply to: BSH Group Redundancies? #279092
    lerch
    Participant

    Re: BSH Group Redundancies?

    They have got to lose 5 engineers nationwide. There work is slowing down.

    in reply to: REDUNDANCIES AT COMET #170054
    lerch
    Participant

    Re: REDUNDANCIES AT COMET

    Yes had the letter today

    in reply to: REDUNDANCIES AT COMET #170051
    lerch
    Participant

    Re: REDUNDANCIES AT COMET

    Which ones then ❓

    in reply to: whirlpool f/f #278464
    lerch
    Participant

    Re: whirlpool f/f

    4812 360 68624 Hose icemaker 😀

    Think this is right if not pm and I will send manual.

    in reply to: Bosch F/F KGN39V00GB01 #278224
    lerch
    Participant

    Re: Bosch F/F KGN39V00GB01

    Bsh are allowed 40 minutes on the last 3-4 modi’s and there is now another one coming just stay the hell away they are a nightmare. :tdown:

Viewing 15 posts - 106 through 120 (of 353 total)