Martin

Forum Replies Created

Viewing 15 posts - 3,331 through 3,345 (of 25,534 total)
  • Author
    Posts
  • Martin
    Participant

    Re: Hole in AEG F88060VI0P Dishwasher Tub – 18 months old!!!

    Steel Putty from places like Halfords can be a solution. Both sides will need the application though to ensure a lasting seal.

    in reply to: Engineer training #423097
    Martin
    Participant

    Re: Engineer training

    Ianyogs wrote:Is that a shitty career choice working for yourself or a shitty job full stop Martin?

    There are many hoops to jump through and hurdles to clear if you plan starting out self employed. Working for a major manufacturer will give good grounding as to what lies ahead for you in the trade. I’m walking away from it having spent 50 years in the business. I can see little long term prospects for anyone these days, those days are gone. I can think of a dozen better trades to take up all of which are hands on with great prospects, though location could be an issue for you.

    in reply to: Engineer training #423094
    Martin
    Participant

    Re: Engineer training

    Shitty career choice. 🙁

    in reply to: Bosch SGS69A02 dishwasher bottom arm not spraying #423081
    Martin
    Participant

    Re: Bosch SGS69A02 dishwasher bottom arm not spraying

    The ‘instantaneous water heater’ will need replacing to cure that fault.

    in reply to: Drain and sink unblocker in dishwasher #423066
    Martin
    Participant

    Re: Drain and sink unblocker in dishwasher

    It should be perfectly safe to use. I hope you solved the problem by using it?

    in reply to: Hotpoint wt960 #422978
    Martin
    Participant

    Re: Hotpoint wt960

    The motor.

    in reply to: Miele washing machines – different country settings #422993
    Martin
    Participant

    Re: Miele washing machines – different country settings

    If you move to Oz then I would think the local Miele agent could reprogram it for you. 💡

    in reply to: Callout charges #422926
    Martin
    Participant

    Callout charges

    Allsorts wrote:Yes, I do disagree with the determination made by the ASA and BIZ.. A company offering a service of £45 diagnostics service may want to offer that service irrespective of the distance involved..

    To elaborate, I may offer a £45 diagnostics to a customer a few doors from…….But then I may offer the same service……………….In an alternative situation, I may offer diagnostics at £45 and callout of £0 ………….

    George, the ruling by the CAP is clear enough and I fear you may fall foul of their ruling if you’re not careful. The specific use of the advertising phrase “No Call Out Charge” is the only issue here. And as long as your various “offers” to your customers don’t infer that phrase you will be fine. Therefore there would be no reason for you to disagree with their ruling.

    in reply to: oven removing table #422846
    Martin
    Participant

    Re: oven removing table

    Yes.

    in reply to: Miele washing machines – different country settings #422991
    Martin
    Participant

    Re: Miele washing machines – different country settings

    yellowplum wrote:Does anyone know what the differences are in these country specific modes?

    The mains voltage of the country. Climate of the country. Some countries like Australia have cold water detergent cycles.

    in reply to: neff dishwasher S434oxogb/20 #422920
    Martin
    Participant

    Re: neff dishwasher S434oxogb/20

    The float microswitch often needs replacing to cure this problem. Part no: 00057553

    in reply to: Servicenet #395433
    Martin
    Participant

    Re: Servicenet

    kwatt wrote:Ignoring your attempt to troll Martin…

    I’m once again here in the USA full of ‘goodwill to all men’ this Christmas season. No time for trolling…… 😉

    in reply to: Bosch SMS53A12GB/51 E17 fault. #422911
    Martin
    Participant

    Re: Bosch SMS53A12GB/51 E17 fault.

    Have you replaced the reed switch Steve?

    in reply to: No heat in Hoover Logic Reversing Dryer #310609
    Martin
    Participant

    Re: No heat in Hoover Logic Reversing Dryer

    Parts should be still available. TOC = Thermal Overload Cutout.

    in reply to: oven removing table #422836
    Martin
    Participant

    Re: oven removing table

    In all seriousness Lee, that is a neat system. Could you please tell us the approximate cost of such a unit?

Viewing 15 posts - 3,331 through 3,345 (of 25,534 total)