[Martin]

Re: Nikkei Nk Lb65E09 misworking with pictures and videos

axxo1 wrote:Hi Martin,
Which one do you mean?
2M,200k,20k,2k?

20k. 😀

[Martin]

Re: Hotpoint WMT03p

It don’t move. That went out with mechanical timers. This one is fully electronic. The old duffer may have been twiddling and getting proper confused. :clown:

[Martin]

Re: Hotpoint Ultima WMA74 door issue

If it worked fine immediately before you replaced the door boot then It would be logical to assume a wire has got damaged or disconnected since. However, if the old door boot was leaking like a collander with holes in it adjacent the interlock then it may be water stained and may have fused the PCB…???

[Martin]

Re: Problem with Bosch Hob

Primrose wrote:Hi, the hob is just a few months old and I keep it very clean, it has been doing this since it was first installed.

Then get it looked at under the terms of the guarantee.

[Martin]

Re: Problem with Bosch Hob

Dirty around the sparker, clean carefully to avoid breaking the ceramic sparker though.

[Martin]

Re: Gas Safe & Proud

GasSafe wrote:
Dear Martin

Thank you for your correspondence.

In this instance I would refer you to BS6891 which states:

8: Installation

8.1 Installation pipework shall be physically protected or located where it is not liable to mechanical damage

If the customer has concerns relating to the gas safety of the installation then he/she can raise a complaint via 08004085500 Option 6 or enquiries@gassaferegister.co.uk .

John Stirling SIIRSM RSP EngTech MIGEM
Technical Support Officer
Gas Safe Register

200 Cedarwood, Chineham Park, Crockford Lane, Basingstoke, Hampshire RG24 8WD
Tel: 0800 408 5500

I would suggest in this instance that the pipework could indeed render itself “liable to mechanical damage” and Squadmans customer should report the guy using the complaints procedure shown in the email above. 🙁

[Martin]

Re: CandY GO FS 262 Washing machine-flashing lights

What components have you checked so far?

[Martin]

Re: Candy GO F 462-80 Washing machine-fault code

What components have you checked so far?

[Martin]

Re: Hotpoint Ultima WMA74 door issue

TheGatherer wrote:Leaving it tonight then I will take the machine out to get the cover off and see if any plug or wire has been dislodged from the panel but not holding out much hope.

I think there’s every hope that has happened as they can easily be disconnected. 😉

[Martin]

Re: Nikkei Nk Lb65E09 misworking with pictures and videos

axxo1 wrote:1)
I have set the multimeter to 200 ohm.

That is incorrect, you need to set it on Kohms

axxo1 wrote:3rd couple (yellow one & yellow one – tacho coil) display shows 1 !

Now test it again on the Kohms scale this time, what’s the reading now?

[Martin]

Re: Reviving towels that have had fabric softener use consis

…….or buy new towels. 💡

They are cheap enough right now at Dunelm Mill (other stores are available) :clown:

[Martin]

Re: Bosch WWF1401 drum noise

Ah I think you may need Specsavers then as I can only find a Bosch WFF1401GB/01.

To test the shock absorbers simply remove the lid and push down and release the drum. ( Much like testing car shocks by pushing on the wing) If it bounces back they’re duff and need replacing.

[Martin]

Re: Reviving towels that have had fabric softener use consis

Half a cup of vinegar is hardly gonna leave a pungent smell after several rinses. Why not see for yourself?

[Martin]

Re: Hotpoint Ultima WMA74 door issue

You’ve knocked the interlock connector plug off?

[Martin]

Re: Bosch WWF1401 drum noise

I’ve never heard of a WWF1401 are you sure you got the ENr number correct? Is it a Bosch?

[Author]

Posts