[MickGeorge]

Re: H/Point FDW60 – no lights

Going back to test out ribbon cable but if not which is more likely to be problem – light/selector/start module or main module?

Anybody offer any ideas please?

Thanks

Mick

[MickGeorge]

Re: Bosch WTL6103GB/01 Codenser Drier – pump?

thanks simon

had removed the screw 😉 but hadnt tried twisting the motor as it all seemed pretty solid and for fear the whole lot suddenly coming loose n spending load of time refitting everything. Just wondered what the knack was to getting the pump out was?

still presuming the front connections are the pump cuz looks like they are o/circ. so new pump required.

Mick

[MickGeorge]

Re: Bosch WTL6103GB/01 Codenser Drier – pump?

Thanks for the reply Simon

yes did take off the hose, even took out the clamp that holds the motor in as i thought that might be fouling the cover – only thing I didn’t take off was the pully system altho that seems clear – looked to me as if it was fouling on the motor coller if anything. wiggled tugged and twisted as much as I dare without breaking but just didnt seem to want to come free.

Do I have to take off pulley system as well?

Mick

[MickGeorge]

Re: White Knight 767C – condenser drier – water in fan chamb

thanks for the repies folks – heres hoping when i phone back clearing the gunge from the rear of the condeser housing has cured the problem then..

mick

[MickGeorge]

Re: White Knight 767C – condenser drier – water in fan chamb

Thanks for the replies folks.

Does that mean yes it could be a blockage in the drain off? – is that what you guys have come across before?

Just out of interest – what about the Hotpoint one- same problem?

Thanks

Mick

[MickGeorge]

Re: Beko WM5140W – pressure sw or module?

Been back today and changed modue – all working fine now so thanks for the replies guys

Panic was just setting in as it stopped and just pumped out for what seemed like a minute before it moved off and started to fill – sigh of relief as thought it was still stuck on pump out.

Test proceedure all printed out and in my fault code bible now. 🙂

Again many thanks guys

Mick

[MickGeorge]

Re: Hotpoint 7823P Dish wash – lid partno

Thanks for the replies folks – much appreciated – think price might put customer off tho even if I can still get one 🙁

Mick

[MickGeorge]

Re: Indesit WIA – loose top c/b weight

Thanks for the reply Hotdog – What type and where do you get your expandable foam from? – never had to use any before.

Mick

[MickGeorge]

Re: Wirlpool AWO/D 4505 – Fault code?

Thanks Chris – very usefull

Mick

[MickGeorge]

Re: Indesit D/Washer IDL40UKC – no heat

Thanks for the reply JJ

[MickGeorge]

Re: Wirlpool AWO/D 4505 – Fault code?

Nobody know how to relate the lights into fault codes on these??

Mick

[MickGeorge]

Re: meggers

Could you send me a copy as well please Martin 🙂

Thanks

Mick

[MickGeorge]

Re: Hotpoint WF 321 dead.

Can you send me a copy as well please Martin – Thanks

Mick

[MickGeorge]

Re: Hoover AM110 01 – Pressure Sw. Pt. No.

Thanks for replies guys.

Looks like 28375042 is the right one and masterparts got some in stock 🙂

Thanks

Mick

[MickGeorge]

Re: Hoover AM110 – PCB mod?

Thanks for the reply Tim – have ordered another module so if that is the same will check that with hoover

At least I know there is no mod 🙂

Thanks

Mick

[Author]

Posts