Muv

Forum Replies Created

Viewing 15 posts - 331 through 345 (of 647 total)
1 2 3 … 22 23 24 … 42 43 44
  • Author
    Posts
  • February 16, 2013 at 9:40 pm in reply to: Miele T7644C Tumble Dryer #390187
    Muv
    Participant

    Re: Miele T7644C Tumble Dryer

    That link seems not to work, but its available via the miele website..

    Martin

    February 16, 2013 at 9:38 pm in reply to: Miele T7644C Tumble Dryer #390186
    Muv
    Participant

    Re: Miele T7644C Tumble Dryer

    Heres a link to the manual

    http://www.miele.co.uk/documents/Get.as … {e5d1b7155a01ef1f3b9c9968eaba33524ee81600d00d4be2b4d93ac2e58cec2d}2520C.pdf

    Take a look at pages 32 onwards..there are ways to knock off this light flashing…
    Seems like it could be just a reminder to clean filters..

    Martin

    February 15, 2013 at 9:39 pm in reply to: meile T234c #390222
    Muv
    Participant

    Re: meile T234c

    Check the stat on the element..remove rear plate..think its a 160 degree one shot type

    Martin

    Also try it on timed dry and not sensor dry

    February 10, 2013 at 6:08 pm in reply to: Whirlpool Generation 2000 Oven #389822
    Muv
    Participant

    Re: Whirlpool Generation 2000 Oven

    If you can supply us with a full model number, or better still all the details you see from either the metal plate, or sticker… Then you should be able to get one from this very site..

    Martin

    February 10, 2013 at 5:50 pm in reply to: Whirlpool Generation 2000 Oven #389820
    Muv
    Participant

    Re: Whirlpool Generation 2000 Oven

    The sparking you describe is more than likely coming from the circular heating element, which surrounds the fan…..

    Usually pretty straigtforward to replace, but if you dont want to attempt it yourself, i suggest you ring for an engineer

    Martin

    February 10, 2013 at 5:19 pm in reply to: Hoover HW6313 washer dryer.. #389819
    Muv
    Participant

    Re: Hoover HW6313 washer dryer..

    Thanks for your helpful advice Martin,it’s much appreciated

    Martin

    February 10, 2013 at 4:50 pm in reply to: Hoover HW6313 washer dryer.. #389817
    Muv
    Participant

    Re: Hoover HW6313 washer dryer..

    Sorry about any confusion

    This is her machine which she purchased from new 10 yrs ago..

    This was a standard call out to a repair

    February 7, 2013 at 9:06 pm in reply to: Miele W828 rinse light flashing. #352862
    Muv
    Participant

    Re: Miele W828 rinse light flashing.

    i’ve just finished doing the exact same job on the EL200 board Replaced relay and fuse,usually cut the old parts open to have a look inside..not seen any as bad as that relay pictured on earlier post though!

    Martin

    February 5, 2013 at 9:08 pm in reply to: Miele W377 heater element #389176
    Muv
    Participant

    Re: Miele W377 heater element

    That’s good news!

    February 4, 2013 at 7:08 pm in reply to: hotpoint cdt40p #389441
    Muv
    Participant

    Re: hotpoint cdt40p

    If you remove the fan cowling from the top of the fan..you can then get at the 2 bolts that hold the pulley on..remove the pulley, then you can fit the belt over the pulley and refit pulley in place..

    Removing the fan cowling gives you the extra bit of space needed to remove the pulley..

    Martin

    February 4, 2013 at 3:22 pm in reply to: Miele W377 heater element #389174
    Muv
    Participant

    Re: Miele W377 heater element

    Thanks for the info dave..

    Martin

    February 1, 2013 at 2:43 pm in reply to: Electra AWM1100A – 30 second Spin #389129
    Muv
    Participant

    Re: Electra AWM1100A – 30 second Spin

    Sounds like a tacho coil or magnet fault to me…

    Martin

    February 1, 2013 at 2:35 pm in reply to: oven tripping main RCD #389166
    Muv
    Participant

    Re: oven tripping main RCD

    The switch that you use on the cooker control panel, to switch the oven on.. Is what i believe samuri means…

    February 1, 2013 at 2:26 pm in reply to: Miele W1714 Waterproof Fault #389227
    Muv
    Participant

    Re: Miele W1714 Waterproof Fault

    It means the water protection feature has been activated…you probably have a leak inside the machine somewhere…maybe from the pump, or the internal part of the waste outlet pipe…


    Power off, if you intend investigating yourself

    Martin

    February 1, 2013 at 2:20 pm in reply to: Numatic George only half working #389212
    Muv
    Participant

    Re: Numatic George only half working

    Could be either the switch or the associated circuit board..

    Martin

  • Author
    Posts
Viewing 15 posts - 331 through 345 (of 647 total)
1 2 3 … 22 23 24 … 42 43 44