Forum Replies Created
-
AuthorPosts
-
Penguin45
ParticipantRe: NEB Vicenza Mirr oven
So basically no heat when in fan oven mode? Check the element behind the rear panel. Pull the plug first.
If you are not confident, check Directories or Repairs@ for a UKW repairer in your area.
Regards,
Penguin45.Penguin45
ParticipantRe: whirlpool fan oven error code F03
Are you quite sure you want to do this?
4812 310 28197 – power unit – over £90
4819 214 78693 – control unit – nearly £50All plus VAT etc.
I would seriously suggest getting some pro help – throwing parts at it will get very expensive, very quickly. 🙁
Regards,
Penguin45.Penguin45
ParticipantRe: Bendix BDW 53 Dishwasher – access to drain pump???
Reversing motor Conor. You can access it from the top by unscrewing the centre column which the bottom rotor mounts on; or you can pull the whole motor assembly from the back, via the rear access panel. Be warned that this is the one with the plastic drive shaft which cracks – only available as a complete motor if it’s gone.
Welcome on board BTW.
Regards,
Chris.Penguin45
ParticipantRe: Bosch sgs 3042 gb 01
Hi MM,
Its just a twist fit magnetic pump – remove the hose from the fill matrix to the sump and you can get it from the front.Easy peasy.
Cheers,
Chris.Penguin45
ParticipantWithout the model number and serial number we’re guessing here chaps.
Guest, if you would be so kind…………..?
Penguin45.
March 23, 2005 at 12:33 am in reply to: zanussi de6744 not working on cycles over 50 degree’s #129643Penguin45
ParticipantRe: zanussi de6744 not working on cycles over 50 degree’s
No particular specialist tools, screwdivers and pliers are enough. However, the IWMS is £60 some, so I’d be tempted to get some help as there is NO guarantee of this diagnosis – it does need to be checked out fully as there are other (admitedly less likely) possibility.
Regards,
Penguin45.Penguin45
ParticipantRe: Do Dyson’s make you scratch your head???
Oh Clive,
Iam vos fui donatus absentis totus nostrum specialis….Chris.
Penguin45
ParticipantRe: Whats the most annoying thing customers do?
BUT – did you fix it………….? 😆
Chris.
Penguin45
ParticipantRe: Fan Oven not working belling forum 317AN cooker
That’s the impossible question……… Your repairer will certainly bill you for an hours work – the rate itself will vary widely across the country; London prices will be considerably higher than up here in Leeds say.
If there is no UKW repairer in your area, look for DASA, Fair Trades, or Trading Standards logos, or seek a local recommendation. Assuming satisfaction, tell them to sign up to UKW!
Regards,
Penguin45.Penguin45
ParticipantRe: Tricity Bendix AW1050
Timer fault according to TDS SparkyP. Save a considerable sum and get a warranted recon from EMW.
Chris.
Penguin45
ParticipantRe: Who owns what and is it any good?
You could always buy a Bosch WTA2— series machine. Then you get a White Knight with a Bosch badge on the front and a nice stainless steel drum. Oh, and a two year warranty. 😯
Cheers,
Penguin45Penguin45
ParticipantRe: white knight cl767 pump !
From memory Paul, it’s about £45, plus the VAT etc…….. Contact spares@ukwhitegoods.com and they’ll get you one quickly.
Regards,
Penguin45.Penguin45
ParticipantRe: indesit wd12uk fault code 3 flashes
In theory……… :rotfl:
Diagram always best course of action.
Luck, regards,
Penguin45.March 22, 2005 at 12:20 am in reply to: zanussi de6744 not working on cycles over 50 degree’s #129641Penguin45
ParticipantRe: zanussi de6744 not working on cycles over 50 degree’s
Strangely enough Ronnie, this fault is almost certainly unrelated to the temperature selection, but more likely to be the water level control system. The clue being the leak…….
There is no simple and easy solution on this one, unless you are very brave I would suggest professional assistance.
Check repairs@ or Directories for a UKW repairer in your area.
Regards,
Penguin45.March 22, 2005 at 12:08 am in reply to: Bosch dishwasher – need new detergent cpmpartment lid #129347Penguin45
ParticipantRe: Bosch dishwasher – need new detergent cpmpartment lid
Mik,
It should be engraved into the top edge of the door inner panel, right in front of the door catch opening.Regards,
Penguin45. -
AuthorPosts
