pmb

Forum Replies Created

Viewing 15 posts - 226 through 240 (of 472 total)
1 2 3 … 15 16 17 … 30 31 32
  • Author
    Posts
  • July 18, 2013 at 4:21 pm in reply to: Beko wm6167w 00 02 in display #397893
    pmb
    Participant

    Re: Beko wm6167w 00 02 in display

    Thanks I did try holding Start button,
    Will go back tomorrow and press start and delay buttons

    June 20, 2013 at 1:49 pm in reply to: Bosch Tumble drier WTE84307GB F11 fault #396602
    pmb
    Participant

    Re: Bosch Tumble drier WTE84307GB F11 fault

    It is usually pcb related i am afraid

    June 20, 2013 at 9:40 am in reply to: Lg wd door not unlocking #396595
    pmb
    Participant

    Re: Lg wd door not unlocking

    Hi allsorts thanks I checked them both and they are fine

    June 5, 2013 at 4:39 pm in reply to: Hotpoint aqualtis F02 #395963
    pmb
    Participant

    Re: Hotpoint aqualtis F02

    😀 thanks alot madangler that is the sort of decisive answer i was hoping for , you are a legend :worthy:

    June 3, 2013 at 6:54 pm in reply to: Bush door seal #395896
    pmb
    Participant

    Re: Bush door seal

    Thanks
    Just ordered from Maddocks
    Peter

    May 31, 2013 at 5:16 am in reply to: Hoover SE147 Module ? #395745
    pmb
    Participant

    Re: Hoover SE147 Module ?

    Thanks Martin
    Sorry It didn’t register.
    ,

    May 30, 2013 at 8:03 pm in reply to: Hoover SE147 Module ? #395743
    pmb
    Participant

    Re: Hoover SE147 Module ?

    Does it come Programmed

    May 1, 2013 at 3:21 pm in reply to: New zanussi tub pulley shaft sizes #394381
    pmb
    Participant

    Re: New zanussi tub pulley shaft sizes

    All my scrap machines were taken away on Monday but what luck just installed a new machine and taken the old bendix machine and the pulley fits.
    It’s saved money and hassle trying to get the right pulley.

    March 31, 2013 at 1:49 pm in reply to: Hotpoint smart card reader #391740
    pmb
    Participant

    Re: Hotpoint smart card reader

    As well as supplying repaired Modules EMW will configure your own new Hotpoint/ Indesit module for a small fee, I had to do this as they did not stock the module I needed.

    December 12, 2012 at 3:57 pm in reply to: Zan W/D no water in on Dry #385355
    pmb
    Participant

    Re: Zan W/D no water in on Dry

    Changed the valve a week ago, let them. Use it a few times and yes it’s OK now
    I have changed a lot of Dryer valve tops but their not working when I check them,
    So now I know they can be intermittant,
    Thanks for the advice

    November 29, 2012 at 7:06 pm in reply to: bosch sms50e02gb/04 not filling #385536
    pmb
    Participant

    Re: bosch sms50e02gb/04 not filling

    Thanks martin that’s good advice, it didn’t seem damp but the customer is very nice so I will give that a try and hope for her sake it works 😀

    November 29, 2012 at 2:23 pm in reply to: bosch sms50e02gb/04 not filling #385534
    pmb
    Participant

    Re: bosch sms50e02gb/04 not filling

    Hi martin thanks for getting back to me just the dropping to one minute, do you need to access fault codes on these?

    November 26, 2012 at 8:33 am in reply to: Zan W/D no water in on Dry #385351
    pmb
    Participant

    Re: Zan W/D no water in on Dry

    That’s what we normally do, had lots of them,
    But this is different, the power cuts off to the valve after the first dryer fill, when the fan kicks in, I think the Zanussi fills all the the way through dry?

    November 22, 2012 at 2:58 pm in reply to: Hotpoint dish dead FDM550 #385115
    pmb
    Participant

    Re: Hotpoint dish dead FDM550

    Does the PCB need programming or is it ready to fit.
    They had smart cards on the Connect Parts.

    November 21, 2012 at 1:16 pm in reply to: Hotpoint dish dead FDM550 #385113
    pmb
    Participant

    Re: Hotpoint dish dead FDM550

    I had looked at door wiring, but maybe not well enough.
    Trouble is its further then I normally go, And it might not be that.

  • Author
    Posts
Viewing 15 posts - 226 through 240 (of 472 total)
1 2 3 … 15 16 17 … 30 31 32