robbra

Forum Replies Created

Viewing 15 posts - 901 through 915 (of 1,090 total)
1 2 3 … 60 61 62 … 71 72 73
  • Author
    Posts
  • February 9, 2007 at 4:21 pm in reply to: replacing door hinge on servis m6513s #203523
    robbra
    Participant

    Re: replacing door hinge on servis m6513s

    If GB Dars don’t supply the parts it’s a cabinet fault and BER but in all the years working on SUK machines I’ve never had a hinge come loose.
    Rob

    February 9, 2007 at 10:36 am in reply to: Bosch tumble…WTA3204GB/09 #196640
    robbra
    Participant

    Re: Bosch tumble…WTA3204GB/09

    Hi Brian,
    Quoted a pcb and she said no so I got her a White Knight which she says is far, far better and the Bosch is in the garage waiting for the summer for me to play with so, I’m sorry I can’t help.
    Surely there are some BSH men who have come across this and can throw some light on it?????
    Rob

    January 29, 2007 at 5:20 pm in reply to: coin in tub #202539
    robbra
    Participant

    Re: coin in tub

    I’m sure this is a Servis
    Rob

    January 19, 2007 at 4:00 pm in reply to: Polaris Twin tub???? #201330
    robbra
    Participant

    Re: Polaris Twin tub????

    worked on the Norfrost and it was from Holland and made by Velo. Still not very good and parts obsolete after 3 years
    Rob

    January 4, 2007 at 7:48 am in reply to: Indesit W83 UK #199393
    robbra
    Participant

    Re: Indesit W83 UK

    Thanks lads, can order it now
    Rob

    December 30, 2006 at 7:18 pm in reply to: how to deal with telephone marketing. #199057
    robbra
    Participant

    Re: how to deal with telephone marketing.

    Best laugh I have had in ages. Thanks for that one Jim
    Rob

    December 25, 2006 at 7:01 pm in reply to: Caress 900 #198663
    robbra
    Participant

    Re: Caress 900

    Hi,
    these machines are usually pretty quiet. Sounds like either the top or bottom weight has come loose which is not unheard of. Top weight is ..er on the top and the bottom is below the door seal. If investigating remember …unplug and power off. Best way to check is grab inside drum and shake it. If weights you should hear a knock.
    Good luck
    Rob

    December 23, 2006 at 8:43 am in reply to: Beko WMA1215 #198628
    robbra
    Participant

    Re: Beko WMA1215

    Hi
    Bekos’ always skip on after filling then should start to heat. Had a few probs with timers in the last month on this model with programmes taking 25 mins with no heat and a new timer cured it.
    Rob

    December 19, 2006 at 7:34 am in reply to: Servis t/dryer belt failure. #198234
    robbra
    Participant

    Re: Servis t/dryer belt failure.

    Hi,
    High melting point grease(about £2.50 a tub in car shops) I use for taper bearings, not too much mind, just enough to get rid of the grip the seal has on the drum and stop the squeek.
    Rob

    December 18, 2006 at 8:38 pm in reply to: Servis t/dryer belt failure. #198231
    robbra
    Participant

    Re: Servis t/dryer belt failure.

    Yep, stick some grease between the rear seal and drum, been doing this for years and never gone back to one
    Rob

    December 13, 2006 at 8:34 am in reply to: Beko (prewash light flashing?) #197775
    robbra
    Participant

    Re: beko

    Hi Mike,
    Tried this and never got it to work but will keep on as it’s an easy call when it does
    Rob

    December 13, 2006 at 12:27 am in reply to: Tricit Bendix AW1400 #197407
    robbra
    Participant

    Re: Tricit Bendix AW1400

    Have given up and she has called Service force out and promised to let me know the fault

    December 13, 2006 at 12:26 am in reply to: Beko (prewash light flashing?) #197772
    robbra
    Participant

    Re: beko

    Prewash light flashing normally means the module is u/s
    Rob

    December 11, 2006 at 10:43 pm in reply to: Tricit Bendix AW1400 #197404
    robbra
    Participant

    Re: Tricit Bendix AW1400

    Thanks Chris.
    Back to square one.
    Dunno what to do about this now as everything seems to check out. No blockage,p/sw ok and so is pcb.Probably give up now.
    Rob

    December 11, 2006 at 7:41 pm in reply to: Tricit Bendix AW1400 #197402
    robbra
    Participant

    Re: Tricit Bendix AW1400

    Hi Alan,
    NTC read 600 ohms, is that ok?
    Rob

  • Author
    Posts
Viewing 15 posts - 901 through 915 (of 1,090 total)
1 2 3 … 60 61 62 … 71 72 73