Forum Replies Created
-
Posts
-
Re: heatrae water boiler
http://www.heatraesadia.com/hs/heatraes.nsf
check out hear there is some helpful advise on there & details of how to get parts etc, i’ve had a few problems with their boilers before but nothing a set of thermistors wouldn’t cure, if the button needs to be reset it means that the control thermistor or control thermostat is not functioning properly, BOTH thermostats have to be changed, High limit cut-out & control one, from memory, best of luck..
Re: How to dismantle a Magimix 5100
Dunno what to make of that, where do i cut it off & where is the metal shaft, how far up does it come up? How is new one then attached?
Re: “The Art O Laundry” is this bible available to
Yeah i know but i’m not from the “Mainland”,,,
i’m from over the pond in Ireland…Re: Tricity Ben’ 551 T’D no motor action
TM551 is the model number & i’ve been told that its a 8uF Cap’ thats neede so i’ll take one of those along & see if it does the trick.
Re: Miele W806.
Yeah very simple as Penquin has said, heater is located at bottom, held in place with clip & seal, check for faulty relay though, i think theres a relay that switches on the heater, i think the relay is located near the bottom where the choke is & cable comes in, (i think, not sure of this model), heater will cost close to £60 & relay would be £25, approx.. best of luck, nice machines to work on.
Re: Mystery tool
I reckon its a home made tool for either removing or putting on door gaskets or their dreadful clamps..
Re: WMA 20P replacement Drum /bearings
Same as you mate i’ve referred all them to Hotpoint, so i’ve never even had to do any, done hundreds of the WMs & 95## series, let me know how you go about it, does the fromt come off & drum come out the fromt on this model or is it taken out the top? Reckon i’ll be doing one soon enough..
Re: Hotpoint B/I double oven BD81, light coming on?
Don’t think the fan should have anything to do with display, as far as i’m aware theres a t’stat on the top of the oven cavity that comes on when it detects heat & switches off fan after it has cooled down, the display lamp gets a feed through the selectors, whether oven, or grill is selected, so look towards at a faulty switch if it stays on??
Re: Bosch Maxx WFO2466 sticking on programme
Thanks lads for your guidance, just to close this, the fault was , really long outlet hose on appliance shoved all the way down drain to the elbow, obviously was restricting the water flow out & may even have been causing machine to syphon,, anyhows i cut about a yard off it & put hook back on & i’ve not hear of any problems since..just another thing the machines finishes @ 001 never goes to zero even though programme is complete & door opens, customer says it used to go to 000..???
Re: Hotpoint TDC32P Condenser Dryer
Seems to be me that customer may not be cleaning either lint filter & condenser cassette, if ther isn’t enough airflow through system it will overheat & blow high level ‘stat, & if door is opened before cooling commences same will happen.. These are always blowing & i keep a good stock of these & relays in my van at all times..
Re: Miele parts diagrams
I’ve the Miele parts software on my laptop, if you give me model number & part description i can get you part number & prices if thats a help.
Re: Bosch Maxx WFO2466 sticking on programme
Cheers lads for the advise, i’ll check drain system next time i call, which is likely to be Monday morn’ wish me luck!
Re: Bosch Maxx WFO2466 sticking on programme
Well i’ve had a look at it now, put some conditioner in dispenser set it to rinse programme,machine took in water & conditioner is all gone, programme said 18 mins at start, but it skips a few mins at finish(from 5) & ends at 1, door opened ok, checked filter no blockages, water went out fast enough, tried again & all ok. Collected readies, happy days, 2 hours later grumpy man on phone , appliance doing same thing. Machine is sitting with 1 on display (is this fault code) door won’t open & conditioner still in drawer??
