[Seamy]

Re: Beko DCU9330R Dryer

Many things you’ll have to check, NTCs, float switch, pump, heater, condenser for blockages.
Time to get out the multi-meter or get a competant person e/g engineer out to look at it.

[Seamy]

Re: Zanussi ZDC37200W Condenser Tumble Dryer – Keeps stoppin

If its sticking intermittantly, there could be something stuck in the fan as its directly connected to motor.

[Seamy]

Re: EOB5630X oven, grill and internal light all not working

I also had thought of clock but in first post it states that clock has been set. Perhaps clock unit may be faulty.

[Seamy]

Re: dead beko cf5533apw – compressor relay or pcb?

Never seen a faulty relay on one, so i’d go for the p.c.b. You can feed the compressor directly with a live & neutral by making up a lead with some push on connectors similar size to the ones used on the compressor.
Look at the connections on the compressor for loose connections & if theres a plug/socket where the loom fits up into the top of compressor cavity (bottom of fridge). Check the cable connections are tight there also.
Is there a defrost timer check its not stuck in defrost position, but this may not have a mechanical timer if its an electronically controlled type.

[Seamy]

Re: Panasonic NA-168VX2WG with U11 Fault Code, please help!

U11 means it hasn’t drained correctly, hasn’t completely drained etc.

Check filter, if you need to, get a local guy to look at it for you, likely to be near £100 less that the manufacturers are charging.

[Seamy]

Re: EOB5630X oven, grill and internal light all not working

Check terminal block for loose connections, check cabling from terminal block, i’m afraid its testing time, time to use a multi-meter.
Power off of course when doing any checks or testing & if you are competant to do it, get someone who is.

[Seamy]

Re: Zanussi ZNG1120M

captaincaveman1 wrote: If you want a proper Zanussi make sure it has the rectangular filter cover on the bottom front right corner.

This Chinese made Little Swan ZWG1120M rebadged Zanussi has a rectangular filter at the bottom right hand side. (I presume you mean not in the kickplate)

Best to look at the sticker inside door, if it says manufactured in PRC then its Chinese.
I don’t mind working on the ZWG1120 & ZWG1140, its the Vestel manufactured one that is torturous.

To be honest Zanussi has moved to the lower end of the E’Lux brand as Bendix has been dropped.
Electrolux & A.E.G machines now on offer with 5 year warranty are decent enough.

[Seamy]

Re: Zanussi ZNG1120M

Spider that you get as a spare should be actually be better than the original one in the appliance. There is a slight difference where the seal runs, they tend to last longer than the original one fitted. You may get away without having to replace the spider though if you want to try just bearings & seal. If its been really noisy though & bearing housing in rear tub is damaged or spider shaft damaged its not worth doing as Martin advised.
Note.. Model is ZWG1120m if you are looking for spares.

[Seamy]

Re: Beko TZDA627 Frost free Tall Freezer

Maybe the compressor is running but not pumping. Or out of gas. Either way if this is the case its not worth repairing i’d imagine.

[Seamy]

Re: Zanussi ZDC37200W Condenser Tumble Dryer – Keeps stoppin

It starts the motor in both directions, capacitor is located near the motor.

this is what you will be looking for…

http://shop.electrolux.co.uk/search?ssv=1256539006

[Seamy]

Re: Lamona 8301

Seamy wrote:Perhaps there is water flooded down in to base and has activated a float switch

Theres a clue in the post..

[Seamy]

Re: LAM8301 Lamona Slimline Fully Integrated Dishwasher

Some Lamona’s are similar to Beko’s.
Sounds like a P.C.B problem to be honest.

[Seamy]

Re: PLEASE HELP BEKO WM5100W Problem

Check to see if any wires have been dislodged during transport, its quite likely that is its moved without the transit bolts being i that the inner drum/tub mooved about too much & maybe tugged off a cable somewhere, i’d be checking the cable loom to door lick first. 💡

Power off of course ❗

[Seamy]

Re: Lamona 8301

Perhaps there is water flooded down in to base and has activated a float switch to run pump continuously. Or maybe the appliance is not emptying the water completely, check drian hose is draining into a basin or bucket to make sure its not clogged.
Power of course if doing any tests.

[Seamy]

Re: stoves gas fan oven ignition help needed

It could be several things, maybe even a blocked intake fan. But unfortunately you can’t do any work to the Gas end of it if you are not registered.

[Author]

Posts