[Seamy]

Re: e/lux dishwasher

Its a complete P.C.B you need, part num’ 1528513003

[Seamy]

Re: Beko WME 7267S Problem

Seems its detecting an unbalanced load and it is probable going back to start of spin cycle, check motor tacho for damage, cable to tacho, loom to motor etc.

[Seamy]

Re: ZWG1140M 9145779820-00 bearing kit

PNC is 914579820 for a ZWG1140

We always put in tub rear which comes complete with bearings & seal part number for it is 4055150017,
normally the spider shaft is good & doesn’t need replaced unless you break the bolt taking it out.
The bearing seal the Chinese manufacturers used in these are crap which leads to water getting into the bearings.
You can get bearings & seal separately.
Seal 4055066726
Front bearing 4055087235
Rear bearing 4055087227
Spider if needed 4055066692

[Seamy]

Re: AEG-Electrulux

A tester wouldn’t find current going up a cable, you need an ammeter for that, a phase tester will only show that there is a live connection to the appliance, you need both a phase & neutral for the appliance to work.
Anyhows its likely the p.c.b is gone on it, post the model & or PNC (9digit) code of appliance so someone can help you with more specific details.

[Seamy]

Re: zanussi zdf 2020 dishwasher out of sync

Check to see what is preventing it from continuing. Likely theres a problem with some of the components. Finish light not coming on is a good clue that it hasn’t finished, time to dust off the multimeter or call an Engineer I guess.

[Seamy]

Re: AEG 5 beeps

Should go into diagnstics, you sure you’ve done it correctly. It will show a motor fault if the motor is disconnected, the motor normally wouldn’t have done damage to p.c.b, but if you have a peep at it you can normaly see if theres burn marks etc on board.

[Seamy]

Re: beko gas range cooker grill f.s.d

Would’nt it be as simple as removing the original one & connecting up the new one.
Its listed as a Leisure product if that helps looking for a service manual, but doubt if they would be too helpful as they only have the basics.

[Seamy]

Re: Zanussi fridge freezer

Model number & or Product number would be a help as they make hundreds of fridge/freezers, it will help someone diagnose the problem on your product.

[Seamy]

Re: Gas cooker, oven not staying lit

You’d need to be Gas Safe registered Engineer to work on a gas cooker.

[Seamy]

Re: Belling Gas Range

Parts are listed as, (try any of these numbers but they may be obselete)
082620711 Main door outer 01631800
082620670 Small door assy 02198550

Get the customer to speak to Glen Dimplex customer care team, the may make her an offer of discount off a new range if she’s lucky.

[Seamy]

Re: Belling XOU90MF – Cutting out – Cooling fan turns slow

Replace the p.c.b

[Seamy]

Re: blinking lights

Maybe a help to describe which lights flash

[Seamy]

Re: Belling Cookcenter 112 dual fuel bottom oven failed

Hard to call it difinitely without checking the appliance but it could be a wiring connection fault at the terminal block, faulty selector switch, dunno if theres a clock on this model & if there is it could be a fault there either.
If element went pop, usually the lamp & fan should work but sometimes the short damages the switch contacts & nothing works, probably best to get an engineer check it out for you.

[Seamy]

Re: AEG Lavamat 16810 wahser/dryer skips straight to drain

Likely theres a blown triac on p.c.b that controls the recirculation pump.

[Seamy]

Re: Leisure dwlt65

If its the heater thats on all the time it could have a welded relay contact & need P.C.B replaced.
It may however be a smell from a faulty overheated overflow switch (float switch in base) thats a common problem with these Beko type dishwashers.

[Author]

Posts