[Seamy]

Re: AEG Dishwasher fav 880701A Enr no 911235122

Check cabling to display p.c.b

[Seamy]

Re: Zanussi ZWD1227W (914604000)

Have you checked the error codes in diagnostics?
Appliance won’t fill till it proves its empty, so start by checking the drain pump, filters, pressure chamber, pressure hose & pressure sw’, sump hose. On washer dryers especially pay attention that heating elements are’nt low reading to earth.

[Seamy]

Re: Miele G1220SC Blows fuse 15mins into cycle?

F14 is heater level switch fault. Most likely its the circulation pump motor not putting up enough pressure, likely theres something stuck in the impellor. Check wiring, especially to & from heating relay & check reading of heater to earth.

[Seamy]

Re: Dishwasher Suppressor Blowing Fuses

Don’t scrap the machine, it would work without a suppressor but its not advised, they are to prevent interference/spikes with electronic devices like hi-fi, tvs radio etc.

Its not an expensive part but they are prone to blowing.

[Seamy]

Re: BEKO DRCS68 condenser dryer fault

In or around 200 ohms would be the reading to expect on a pump, in the first part of the post you said it ran when power was applied to it. Maybe theres an intermittant fault with the coil, luckilly parts are not to expensive for Bekos.

[Seamy]

Re: Beko DE 3542 FS – Low Jet Pressure

:lesson: Well for a start never over-ride a safety switch, an appliance has a door switch to prevent it working while the door is open. :lesson: Why not try the appliance to run as it should & start a program, let it fill as normal not by filing with a hose, when you hear it has started open door, you can see whether spray arms have turned by taking note of the position.

Theres an issue with the feeder hose to top spray arm not locating correctly, meaning that when top basket is pushed back it doesn’t go in properly & not enough water comes through top spray arms. If both spray arms don’t turn correctly its likely theres a motor problem, that could be a defective cap’ as advised or a mechanical problem with the pump, worn impellor maybe. If you’re lucky it could be just a blockage in the impellor or pipes to or from circulation pump.

[Seamy]

Re: ZWD12270W washer dryer program running too fast not heat

Most likely theres an NTC fault & its skipping the heating section because it thinks its hot or is erroneously getting a wrong temperature reading from a defective NTC. Its not plumbed to hot water by mistake is it?

[Seamy]

Re: Miele Dishwasher G1220SC Error 14

F14 is a heater (high) pressure switch problem. Mostly its a blockage in the circulation pump impellor, very easy to split & check.

The program is interrupted and the drain pump is operated.. The display shows the message Technical fault code F14 — Call Service Dept. The buzzer is activated for 2 minutes. The circulation pump operating after a water intake step, the heater pressure switch is checked to ensure that sufficient water pressure exists in the wash water circuit. For this the heater relay must have been activated.

Cause:
Heater pressure switch B1/13 defective.

Remedy:

1. Check the heater pressure switch.
2. Check the connection plug and wiring harness.
3. Replace the heater pressure switch, if necessary.

Cause:
Circulation pump inoperative. Circulation pressure too low (no pressure at heater pressure switch). Pump may be blocked by foreign objects.

Remedy:
1. Check the circulation pump for foreign objects.
2. Check the circulation pump capacitor.
3. Replace the circulation pump, if necessary.

Cause:
Foreign objects in heater pressure switch.

Remedy:
Replace the heater pressure switch.

Cause:
Flow meter B3/4 defective (incorrect water quantity registered).

Remedy:

1. Check that the plate with the reed switch on flow meter B3/4 is seated correctly.
2. Check that the reed switch connection plug is seated correctly.
3. Replace the reed switch, if necessary.
4. Check the control lead from the electronic to flow meter B3/4.
5. Remove the water inlet mixer and replace if necessary.

Cause:
Circulation pump defective.

Remedy:

1. Check the circulation pump power supply.
2. Check the circulation pump capacitor.
3. Replace the circulation pump.

Cause:
Circulation pump winding overheated; winding protection has cut out.

Remedy:
Replace the circulation pump.

Cause:
After a water intake step, heater pressure switch B1/13 has not opened switching steps 11–12 and 21–22. This starts the anti-stiction routine.

Remedy:
Replace the heater pressure switch.

Cause:
Motor capacitor defective.

Remedy:
Check the motor capacitor and replace it if necessary.

Cause:
Contacts on heater pressure switch B1/13 short-circuited. Contamination on the plug of the heater wiring harness and a conductive connection between the plugs and the main harness causes a short circuit to the contacts.

Remedy:

1. Replace the heater wiring harness.
2. Replace heater pressure switch B1/13.
3. Reconnect the two individual plugs from the main harness AMP 6.3 x 0.8 and apply new insulation sleeves. Do not interchange the plugs.

[Seamy]

Re: zanussi zwf1421w electic shuts off duing cycle

Maybe motor shutting down on overheat protection or not turning because of carbon brushes are worn.

[Seamy]

Re: beko dryer belt

Theres 2 belts on it, small belt kit 492204404, large belt 2962470100

[Seamy]

Re: zanussi washer/dryer ed4 problem

Fault E73 means there is a fault with the NTC located in the dryer duct, this can be caused by excessive heat, possibly by hot water as COLD water which is required constantly during the drying cycle to condense the steam.

[Seamy]

Re: Beko WM5140W Fault/Error Codes

When you say it “started suddenly” do you mean it started without button been pushed, or does it go into full spin suddenly on wash?
If the latter most likely P.C.B is faulty, but could be motor tacho or wiring from motor to p.c.b.

[Seamy]

Re: zanussi zde47100 tumble dryer

Check filter light comes on every time a programme finishes, is there any fault code flashing? Post how many times it flashes & hopefully someone will be able to help you. No heat points to fault with heater or NTC or P.C.B

[Seamy]

Re: Beko WM5101 titsup – help please

Not sure but the wagon wheel type biscuit thing you describe could be a pressure switch.
Power on most Bekos will come in on the maims cable through a filter/suppressor onto mains switch.
Most likely from what you describe so eloquently , the P.C.Bs away, not an expensive part though compared to most makes. Part num’ 2324100400

[Seamy]

Re: zanussi washer/dryer ed4 problem

E73 fault points to NTC failure in the dryer duct most likely, ED4 is normally an erroneous fault raised when there is a short to earth in either the dryer or wash heater elements, can also point to faulty p.c.bs most likely the drying one or wiring.

[Author]

Posts