Forum Replies Created
-
Posts
-
Re: Hoover HNL 6166-80 FL no heat
Criscold wrote:Re-Check NTC Resistance
Ohmic values of NTC Probe are:
20 Kohm at 25°C – 2.14 Kohm at 85°C.I will check the NTC again.
Re: Zanussi ZG1120M Cuts out, display goes blank.
I checked supply and for loom damage. Tightened connections to PCB.
Asked customer to plug into different socket.
Everything came back to a board fault which is why I sent to EMW. Now I don’t know if to suspect a PCB fault that EMW couldn’t find or something else?Re: Hoover VH W6540-80 Washer/Dryer TD overheat stats tripp
Martin wrote:
So is it a 180 degree TOC that’s fitted on that machine?I haven’t managed to get back to it to check, I will update you when I find out. My guess is it will be.
Re: Hoover VH W6540-80 Washer/Dryer TD overheat stats tripp
That’s what I thought, the valve that switches on for 2 second bursts during drying is running water into the condenser not the dispenser.
Re: Hoover VH W6540-80 Washer/Dryer TD overheat stats tripp
Martin wrote:
GIAS wrote:
At the beginning of each Phase of Drying and after each Thermo-Spin, is activated for 2 seconds the Solenoid Valve EV1, in order to fill the siphon of the Detergent Load Hose and prevent the escape of steam during the Drying Phase.Lightbulb moment…….?
I don’t know about a lightbulb moment! My head’s starting to hurt.
What’s the ‘Thermo-Spin’? The valve (I don’t know if it’s EV1 but it supplies the hose that goes round the back of the tub and into the condenser)seems to operate for the 2 seconds but “Siphon of the Detergent Load Hose” suggests it’s in the detergent dispenser!
Re: Hoover VH W6540-80 Washer/Dryer TD overheat stats tripp
Martin wrote:
GIAS wrote:
Solenoid Valve is shut off for a time not exceeding 3 minutes, and the length of the pause is inversely proportional to the Drying Air Temperature detected by the NTC sensor.That makes sense 😕
So I assume the hotter the NTC senses the more the valve will release to bring the condensing temperature down!
If that’s the case, testing without damp washing would mean the NTC would be hotter therefore release more water….I think!
Or would the short release of water bring down the temperature quickly shutting off the valve hence only giving a short burst? :haier:Re: Hoover VH W6540-80 Washer/Dryer TD overheat stats tripp
I thought it was only operating for about a second when I tested, I will double check. I’m surprised it’s only 5 seconds every 3 minutes doesn’t sound like it would cool enough to work.
Thanks for the information :).Re: Hoover VH W6540-80 Washer/Dryer TD overheat stats tripp
timdowning wrote:I’ve never looked that closely at the water side of things but sounds ok to me…
So does the inlet valve for the condenser only operate for about 2 seconds every 2 or 3 minutes, that doesn’t sound right to me, I’ve always thought they run for most of the time?
Martin wrote:Ditto Tim’s comments. Also the resettable Safety TOC has been uprated from 160c to 180c to overcome the instances of nuisance tripping. (Part no 41034167) the later TOC’s have GREEN numbering on the side for easy ID. 😀
I assume both the resettable TOC’s uprated? both had tripped.
Re: Hoover VH W6540-80 Washer/Dryer TD overheat stats tripp
When I removed the heater box it it looked like the condenser was part of the tub, I don’t think it was fitted on the back like the earlier machines. The chambers were clear and there water no filters either.
Re: samsung bf641 oven
Was the code confirmed and what was found?
I have had a call from a customer who also says this oven is displaying an E21 code.Re: WAE24164GB/22 all spin lights and wash light flash
Just an update, after returning to this machine I tried to reset again before, it reset this time after 3 attempts.
Not sure what I did was different on the third attempt, I was always conscious to hold the spin button in for more than five seconds before and after rotating the control knob the one position.
Thanks for the help MartinRe: WAE24164GB/22 all spin lights and wash light flash
Logic suggests that if the motor was disconnected it would sense a fault and not reset 😕
After replacing the brushes I checked the resistance through the armature and winding and for an earth fault everything appeared good but I will go back and give this a try.
Thanks.
Re: WAE24164GB/22 all spin lights and wash light flash
Thanks Martin,
I did hold the spin button for a good 5 seconds.
Does this machine definitely have to be reset? I have never had to do this to a machine with the silver touch buttons before.
