[wilf]

Re: Hotpoint clicking

what type of door lock is on them?

wilf

[wilf]

Re: Hotpoint AQXXF149PMUK

had the same thing on one of these last year cleared the pump it then pumped then nothing put it down to pcb as everything else tested ok. horrible machines thankfully not too common.

wilf

[wilf]

Re: Bosch washer – WAQ28461GB/12 – bearings shot

so as I unblocked the pump on a Bush machine I said ” how long you had it?”
“four years first time its gone wrong”
£160 thats less than 80p per week how can you say this is crap?
the moneys in the soap powder not the machine and not repairs.we are the last in the long line of repairers irons toasters vacs soon bigger stuff i.e. us

wilf

[wilf]

Re: Bosch washer – WAQ28461GB/12 – bearings shot

bosch not what they used to be. had four or five now, under three years old and bearings u/s. its the ones with the round filter cover dont know where these come from.

wilf

[wilf]

Re: zannusi td4212 916092302-01 poor drying

condensation forming would indicate air flow fault. is it blowing ok?

wilf

[wilf]

Re: bosch cond dryer

just for future ref I’ve been back to this and changed front ntc more out of hope than science but that was last week it ran ok then and I told the customer to get back if anything wrong . hav’nt heard anything so I assume its ok. measured the resistance one against the other as I fitted it and got about 1K difference .

fingers crossed wilf

[wilf]

Re: Hoover DYN9124 F08.

check heater for earth faults I’ve had a 62 Megohm fault upsetting the whole machine.

wilf

[wilf]

Re: gorenje hob ect2800p2

like I said very strange. modern house wiring all good 30a dp switch. customer is smart man and has tried leaving it off for several minutes but he assures me he has had to go through this procedure several time due to power cut and accidental switching of the wall switch. oven is on same circuit via a spur even with this off the same thing happens when its powered up it works ok .not one I’ve seen before. this is one of those “oh by the way do you know anything about……jobs” while looking at another job.

wilf

[wilf]

Re: gorenje hob ect2800p2

it is on a 30 amp supply you have to disconnect from supply (switch off) take the base off unplug the pcb wait a minute reassemble then switch back on. all very strange. I suspect the pcb but at £200 plus I dont think its a runner hence asking about replacement sizes.

wilf

[wilf]

Re: beko dsc64w dryer

heater ntc 19500kohm at 25 centegrade door ntc 1200 ohm 25 centegrade too far out and no heat

wilf

[wilf]

Re: hotpoint HVL241 error

thanks pressure switch is anlogue and I can hear it working when blown havnt got one to try with but I didnt meter it but got a positive click.

wilf

[wilf]

Re: candy hja8513

switch cleaner did the trick hope it lasts. its always the ones out of town that seem to need a return call, still keep my fingers crossed.

thanks again wilf

[wilf]

Re: candy hja8513

thanks I’ll give it a try

wilf

[wilf]

Re: beko dryer DCU8230

just in case anyone else has similar fault it was the heater ntc it seems readings outside design limits cuts out heater.had an old wma ntc in my box hooked onto the leads and away she went so ordered new heater.
heater ntc should be 19500 ohm @25c door ntc (orange wires) should be 1200 ohm @25c

regards wilf

[wilf]

Re: beko dryer DCU8230

just looking through parts list and I see a door ntc any idea where this is and how to access it? I now suspect the high resistance leads I mentioned earlier go to moisture sensors Im going back tomorrow but any technical would help to lessen the learning curve.

thanks wilf

[Author]

Posts