[Bernie]

Re: Hoover HNC380-80 condenser dryer, stopping after reversi

I was given part number 40003336 but it was the wrong one.

I do still requirer the part number for the exhaust stat, if you would not mind.
Thank you Loopey

Bernie

[Bernie]

Re: Hoover HNC380-80 condenser dryer, stopping after reversi

Thank you very much Loopey
Bernie

[Bernie]

Re: Hoover HNC380-80 condenser dryer, stopping after reversi

Please
Does anybody know the part number for the programmed PCB?
I found a part number for the unprogramme one.
Also the part number for the exhaust stat.

Thanks Bernie

[Bernie]

Re: Hoover CA230 Timer Terminations

This website has:-
Hoover CA230-003 Washing Machine Technical Repair Service Manual CDC-2521
But you have to buy them, I have never used them my self

http://www.mauritron.com/hoover.html

[Bernie]

Re: Bosch dishwasher SGS5342GB/17 FD8011130111 stuck at 13

I have now been back to this and have now come to the conclusion that there is in fact nothing wrong with it and that it was the customer that had caused the problem. I did not have time when I first went there as I had fitted it in between other calls.

Thanks to all of you that took the time to look and reply
Bernie

[Bernie]

Re: Bosch dishwasher SGS5342GB/17 FD8011130111 stuck at 13

I haven’t yet, but would that have 13 mins in the display ?

But thanks for the reply
Bernie

[Bernie]

Re: Creda 37761 – Belt Change

The belt is an EL1860H7 which is about the same size as the drum you have to stretch the belt about 4/5ins
Top, facia and both sides off you can then fit new belt around the drum, it is worth checking that the Drum Shaft and the 4 front bearing pads are ok. Fit the left side (looking from front) and facia back lay it down on the left side, I thread some cable (from an old loom) through the vents in the base of the machine around belt and back through vent hold them with a pair of mole grips and pull to get the belt onto the motor that’s about it. Good luck
Bernie

[Bernie]

Re: Bosch Dishwasher SHV43A03GB/42 FD8212470164 drain pump k

Thanks for the reply Pinky.
Not quite sure of your reply, do you mean it’s the PCB and could be something else that has caused it?
What is “the water point motor on the heater “?

Bernie

[Bernie]

Re: Zanussi ZWF1220w Will not pump out when put through a pr

Finally got to the bottom of this one it was the pcb.

Thanks to all off you for your help and suggestions
Bernie

[Bernie]

Re: Candy CDV262 dryer keeps knocking out the one shot cut-o

Thanks for that Dave, that will give me Something to look for. This one does not have the fan below the element.

Bernie

[Bernie]

Re: Replacement cut-out/stats for Hoover/Candy t/d heater el

Loopy you said that you have been using the 1 shot thermal fuse, part number 40001753 and you have had no problems.
I cannot see how this will work as the thermostat is 130deg and that one-shot (part number 40001753) is only 85deg. The original one-shot on the heater is 206deg.

[Bernie]

Re: Zanussi ZWD1682W

If you would like the wiring diagram for this machine let me have your email address

Bernie

[Bernie]

Re: Bosh WFK2801GB/01 1min in display

It has come up before have a look here:-
http://www.ukwhitegoods.co.uk/modules.p … +wfk2801gb

[Bernie]

Re: ZAN ZJD12191 Fills then stops

Check you email

[Bernie]

Re: Replacement cut-out/stats for Hoover/Candy t/d heater el

Thanks for the part number for the one shot thermal fuse loopey.
You wouldn’t happen to know part number for the other one the blue spot?
Bernie

[Author]

Posts