cab

Forum Replies Created

Viewing 15 posts - 151 through 165 (of 423 total)
1 2 3 … 10 11 12 … 27 28 29
  • Author
    Posts
  • October 12, 2007 at 4:12 pm in reply to: Marks on Whites Zanussi FJS1397 #230425
    cab
    Participant

    Re: Marks on Whites Zanussi FJS1397

    Hi is the vent steam hose intact? I have had them being dragged into the tub rubbing on the drum and transfering onto clothes!

    cab

    October 12, 2007 at 3:47 pm in reply to: samsung wm error code #230642
    cab
    Participant

    Re: samsung wm error code

    thanks going to it in the morning.

    cab

    October 6, 2007 at 1:01 pm in reply to: LG direct drive #229606
    cab
    Participant

    Re: LG direct drive

    dont know if this number is still ok or not!

    0870 607554 – Peter Butt

    October 5, 2007 at 10:30 pm in reply to: ZANUSSI ZDT 5052 #228960
    cab
    Participant

    Re: ZANUSSI ZDT 5052

    is it built in to a sink and it is filling from the sink

    cab

    October 5, 2007 at 10:26 pm in reply to: AEG washer dryer E20 fault. #229314
    cab
    Participant

    Re: AEG washer dryer E20 fault.

    yep, condenser is probably blocked

    cab

    October 5, 2007 at 10:23 pm in reply to: Electrolux slimline dishwasher – locking fill valve up. #229310
    cab
    Participant

    Re: Electrolux slimline dishwasher – locking fill valve up.

    me thinks new sump required

    cab

    October 5, 2007 at 10:17 pm in reply to: LG 12126rd noisy motor #229396
    cab
    Participant

    Re: LG 12126rd noisy motor

    hi what is the noise? they do tend to make a `groaning` noise at low speed tumble. The only other problem I have had is after fitting a new stator it clicked, one of the coils was damaged. Bearings are crap. probably that.

    cab

    October 5, 2007 at 10:10 pm in reply to: LG WD 1255FHB #229432
    cab
    Participant

    Re: LG WD 1255FHB

    hi front panel off is a must, but what i do to fit the spring clampy thing is undo one of the tub bolts around the eleven oclock positon, put a piece of wire thru the hook part eye, wrap it around the bolt and tighten it which gives you both hands free to pull the other part around.
    hopr this helps

    cab

    October 5, 2007 at 9:56 pm in reply to: Zanussi ZCM930x (Product 941309678 ) Door Assembly Query #229667
    cab
    Participant

    Re: Zanussi ZCM930x (Product 941309678 ) Door Assembly Query

    yep I hadnt counted the spacers handle etc.

    cab

    October 5, 2007 at 7:24 pm in reply to: LG direct drive #229604
    cab
    Participant

    Re: LG direct drive

    check fault code section, see to remember I had one and a wire was broken on the motor plug.

    cab

    October 5, 2007 at 7:21 pm in reply to: Zanussi ZCM930x (Product 941309678 ) Door Assembly Query #229665
    cab
    Participant

    Re: Zanussi ZCM930x (Product 941309678 ) Door Assembly Query

    looks like the door comes in about 8 different bits 😯

    cab

    October 5, 2007 at 7:16 pm in reply to: Zanussi ZWX1605w #229705
    cab
    Participant

    Re: Zanussi ZWX1605w

    97391451 72 70-00 / 0 comes configured. can you get into diagnostic to check fault code?

    cab

    September 2, 2007 at 4:37 pm in reply to: Zannusi zbs703b #226331
    cab
    Participant

    Re: Zannusi zbs703b

    you have mail.

    cab

    August 31, 2007 at 6:54 pm in reply to: Zanussi ZWD1271W Washer Dryer #225293
    cab
    Participant

    Re: Zanussi ZWD1271W Washer Dryer

    technical bumf says for E21 could be an element leaking to earth!

    cab

    August 13, 2007 at 4:25 pm in reply to: HP dw #224244
    cab
    Participant

    Re: HP dw

    hi, the button layout on the control panel is the same except the on/off and prog lights are on the opposite side.

    cab

  • Author
    Posts
Viewing 15 posts - 151 through 165 (of 423 total)
1 2 3 … 10 11 12 … 27 28 29