Forum Replies Created
-
Posts
-
Re: Whats the most annoying thing customers do?
as per Martins USA experience, I have added this to our t&c’s, pre pay customer, one sighting of a dog running towards me to say “hello” and I am out the door.
martin wrote:“This is a courtesy call from the General Electric Service Department. Our technician is on his way and will be at your house within 60 minutes, please be sure to lock all animals away from the work and access areas, thank you!”
Re: whirlpool 20 RBD4APT water leaking from ice maker
easy to prove if its the valve leaking, just turn the water on and see. Could be nothing more than the water pipe into the ice maker or the plastic funnel being frozen or blocked with something. Could also be a overfilling ice maker, older ones were mechanical and could be adjusted, not that you should ever need to. TBH its a case of getting out there a taking a look
Re: SMEG APWD126 DOOR SEAL
johnnyj wrote:Thanks i was beginning to lose my mind on this.
Maybe because its branded an Appell appliance?
Re: Smeg DC122W circulating issues
OLLIE2806 wrote:Thanks, Ill give that a go, Any ideas why the salt light would continually stay on?
aside from the obvious one? 😮 Have to short out the reed swtich to confirm its a dodgy reed I guess, should think un related to fault unless there is a major pcb issue.Re: Smeg DC122W circulating issues
this could be a collapsing pump- heater hose, especially when water is hot part number 758973776, the new one is strengthened with ribs.
Re: FABER Apart PBXA60 Cooker Hood
mike412 wrote:For the benefit of all, the New Faber UK agents are AWS, Norwich.
Tel 01603-412324
Excellent Service.
Mike
Have to laugh, no ones told us yet!Re: smeg df613sdx float
973830020
have to ask Bob, whats wrong with the old one? Mouse eaten it maybe?
Re: asko w6461 soap box hose
part number for the dispenser/ tub hose is 8061628
the thin vent hose to the tub is 8061736
Could try David at ISE as they have access to these although the main hose is not the same as any ISE machine, the vent hose from a W1606.Re: Bosch WET2820GB/01 Changed motor end frame
Not done one of these for years but is it possible to fit the field coils the wrong way round somehow? have a distant memory of such a thing.
the pcb triac is available on its own for that one 00155272 so may be worth a punt.
Re: Europarts Maddocks
kwatt wrote:Just to offer a different view and, I’m not saying it’s right, wrong or indifferent…
Small accounts are a complete PITA to operate.
You have the ones that are as good as gold, pay on time and never cause an issue.
Then you have a good chunk that don’t pay on time, you have to send letters, get all nasty and so on just to get paid.
K.eastlmark wrote:
(and it was on a payment with order basis so its not like they had to keep a credit account for me)
Re: Miele G692SE Plus 3 Fill Problem
jag-12 wrote:Above machine starts the program by filling fine for a few seconds, then stops and fill/drain light flashes. After a couple more seconds the light turns solid and the machine starts to fill again. this cycle continues about 5 times then the machine just sits with the light flashing.
Base is bone dry and have checked the flowmeter reed switch operates with a magnet, and it seems to be pulsing on and off with the water flow.
Disconnecting the flow meter makes no difference.
Have checked all connections are tight and am getting voltage at flowmeter.
What am I missing please.have had this in the past, all you can do is trace the flow meter wiring to the pcb, if all ok then its a pcb fault, assuming you can hear the water coming in at a reasonable rate when it is filling.
Re: Baumatic BDI631 dishwasher
any idea who makes that one?
if that’s the Hairer one, usually an earthed circ pump locks the module, try unplugging the pump and see if you can set a prog then.
Re: Football Season 2013/14
not a great day to be a Spurs fan, loosing Bale (had held out vain hope the deal would collapse at last minute) being far worse than only loosing to the Arse away by a goal. Worse though is the fact that we have not yet scored a league goal in open play.
Re: Miele WS5425 no heat
johnnyj wrote:Can anybody help please was asked to look at a miele ws5425 washing machine for the local football team not heating, i’ve checked the heater and wiring all seems okay can anybody give me some Pointers Please JJ
Heater is connected straight off the terminal block via a relay. Need to check if there is a feed to low voltage/ current side of the relay, if so then its the relay at fault, if not then most likely its the electronic.
Would make sure it is not heating first though, get a lot of phantom no heat calls these days…..
