[electrofix]

Re: ceramic hob stays warm when off

got to be the energy regulator ( simmerstat)

Dave

[electrofix]

Re: Panasonic Microwave Oven NN6850 Internal Fuse

non professionals please note

microwaves use very high voltages (5000v) you can get a shock from an electric socket and live but not from a 5000v microwave

if you dont know DONT TOUCH !!

Dave

[electrofix]

Re: hotpoint aqualtis weight coil springs

if its under 5 years old get hotpoint to do it (5 year part warranty)

if its over scrap it as you will fix the tub and the electronics might fail

Dave

[electrofix]

Re: Manual for Bosch fridge freezer

have you tried emailing them ?

Dave

[electrofix]

Re: Miele condenser dryer T4839C F2 fault

very possibly but if its tripped again it means its overheating

Dave

[electrofix]

Re: Amica Service

did not know it had gone but now you mention it i dont get the emails anymore

what happened ans what do amica do now ?

Dave

[electrofix]

Re: Siemens F/Fzr obsolete after 5 years?

martin is correct

go to

http://www.siemens-home.bsh-group.com/u … pare-parts

you can look for yourself electronic panel is item 0151 but if you open it it says use item 0161

Dave

[electrofix]

Re: creda C361E clock not comig on

just guessing here but

assuming old element is open circuit then the live wire to the element is not held at neutral so can float and may have enough leakage to power a clock. when you add the new element it hold the wire down. i would bet if you removed 1 wire from the new element the clock may come on

sounds like you may have blown a safety stat or the like

Dave

[electrofix]

Re: Zanussi Washer Dryer not drying

first you have to find out if the element is being turned on and the fan is running

Dave

[electrofix]

Re: Dishwasher not working

there are plenty of post covering this one

https://www.ukwhitegoods.co.uk/forumsph … 20800.html

try this one

Dave

[electrofix]

Re: WHITE KNIGHT C44AW HEATER PROBLEM

short answer no

if the safety button tripped its normally poor air flow ( kinked or blocked hose/ blocked filter)

these elements just fail this way

fairly simple fix.
unplug, take lid off
the rear has to come off so the wires from the casing to the rear plate have to be disconnected. take photos, draw diags but you musk know where to put them back

then lay machine on its face and just remove the top section of the rear

swop element ( taking note of the orientation of the element holders)

and re assemble

https://shop.ukwhitegoods.co.uk/ps3402- … er-element

Dave

[electrofix]

Re: ‘Premier’ Type E72A/B14401TE oven thermal cut out

doing a search found a post with a similar subject

viewtopic.php?f=36&t=3197

but digging a bit more found possible smeg part number SMG818730625

have posted a picture from Qualtex and they are showing stock

the only thing I can be sure of is the picture actual or generic you would have to order and check or ask them. checked connect and they say it 90 degrees so I don’t know

hope this helps

Dave

[electrofix]

Re: Prima (Whirlpool) LPR602 pumping in short bursts

water metering no. Water would have to flow so prog could detect failure

assuming no fault codes as it just restarts

do the lights on the prog go dimmer as it restarts ?

if yes or even as a try look inside timer pcb to see what sort of power supply it has. if its a capacitor style using a large 1uF of 1.5uF then change it and see what happens

Dave

[electrofix]

Re: John Lewis JBLIOS602 overheating

sound like the relay on the main board that controls the element might have stuck closed. if not its a complete new board

Dave

[electrofix]

Re: Beko DCCC4521 oven wiring

have sent you a pm

Dave

[Author]

Posts