[electrofix]

Re: ESS Multi Assistance UK

been paid for every job so far but had to push but also swung on the price to make it worth while will not do too many jobs but when they accept £80 c/o its worth a go i only used two butt connectors and a gallon of diesel this time

[electrofix]

Re: 60Hz

think it was them who supplied machine but thank for number

have scrapped machine for 60hz work will try it on 50hz when on dry land and report back

thanks for replies

Dave

[electrofix]

Re: 60Hz

this machine supplied to work on 230 60hz but motor clearly labelled 50 hz pump has been changed and works ok
need to tech advice from manufacturer but its a hoover not sure what they will tell me

Dave

[electrofix]

Re: Hoover HNC 170 Heater Change?

have done a few of these if you remove front of machine and also remove front pulley and frame you can leave drum and belt in place and removing one wire at a time you can change heater just by reconnecting each one using one arm not easy but possible cant imagine how they put these together in the factory

Dave

[electrofix]

Re: Fisher & Paykel Dishdrawer F1 fault.

got similar fault called out to one blowing rcd

base flooded seems to be bottom draw that may be leaking but not certain is there a common fault here ?

Dave

[electrofix]

Re: AEG “Clicking” washer

agree had this fault a few times very common

Dave

[electrofix]

Re: Duel Cooker Elements

put it in the oven at home for a few hours that should do it

if not a blowlamp work wonders

had a customer who steam cleaned a hob not so long ago quick go with a blow lamp job sorted

hope this helps

Dave

[electrofix]

Re: Whirlpool ADP262WH dishwasher.

if valve has a safety hose to valve try taking this off double it over and put elastic on it to seal

then try machine if it is valve fault will reoccur if not look elsewhere

if it works put hose back and try again to see if it just had a good day and worked for once

you obviously can only leave hose off while you are with the machine and testing it

this should condem or eliminate valve

hope this helps
Dave

[electrofix]

agree with above probably pressure hose with small hole in it

a quick visit to b & q for plastic hose does the trick

as an explanation to why it only happens on rinses the machine takes in more water which lowers the drum and opens the hole in the tube

hope this helps

Dave

[electrofix]

Re: Hotpoint WF430 Bearing Kit

the first one i had of these i fitted early tub to machine with bigger spider and bea not had any complaints yet
no news is bad news as they say
did not notice weight sizes any difference but i did not have them together to compare

Dave

[electrofix]

Re: Hotpoint WF430 Bearing Kit

thanks for offer Dave but have already sorted from loose bearings i had around but now i need another set and dont know if the next set will be the same will ring Qualtex next week and see if they have any idea

thanks again for offer

Dave

[electrofix]

Re: Hotpoint WF430 Bearing Kit

just got a gen bearing kit for above 1604600 after waiting 3 weeks and hotperloni have wronly packed it and included a 6207 bearing which is miles too big
😡

[electrofix]

Re: whirlpool awd3961

thanks will check it

Dave

[electrofix]

Re: bosch dryer 3204gb

never really got an answer to this one dryer seemed to right itself but has now been scrapped by customer as the heater failed still have dryer looking for s/h heater or will try to fix original if i get time

Dave

[electrofix]

Re: Belling Cooker 626

if the elements are glowing red no matter where you put the knob then the simmerstat is faulty

the simmerstat is behind the knob i am sure dave can come up with a part number if you want two

Dave (electrofix)

[Author]

Posts