Forum Replies Created
-
Posts
-
Re: Diplomat ADP 8234 Tripping fuses
ya u need a new capacitor if its swallon at all and if it got they grey stuff comming out it .
new ones are metal and are more hardcore old ones are plastic and are weak.Re: DIPLOMAT ADP 8352 NOT DRAINING PROPERLY
if not draining and u heara very quiet humming when u put head to door when u first start a programme and if u check spigot where it pumps out most likely u have a seed or glass caught in pump propellor.
unplug machine<<<<
if this is so can be cleared from inside tank hole at very bottom use a metal coat hanger and fead it down the bottom hole where the plastic line is over the hole and u can push the propellor the other way that will relase the seed and let it drain
ps have to becarefull not to use anything sharp and be carefull not to rip the rubber pipeRe: adp 8902 problems
may be thinking of the wrong machine here if this sounds about right hope it helps some ( if not ignore.) ps my grammer is bad.
going by memory is it a slimeline dw red led lights ?
if it is try holding down the programme button for 10 secs and it will cancel any programe it stuck in and u get …** on leds.to reset pcb ie test programe turn machine of then back on and before light comes on u have to hit the programe button either 4 or 5 times fast before the light comes on and u get *…* on the display on some models u hit programe once more to get 1 light *….. or …..* forgot which way then you tun the machine of then back on and hold button down again to clear any programeand get ….** again.
it been know that if programe is in test programe it will over fill in on slimeline machine as it fills to full machine level.
people trying to use the 70.C wash hit the button to many times before it comes on and bang u in test programme.
low insulation on motor/machine has been all so know to start a test programe normally due to leak thats been in base and made the motor get wet and sucked the water up.Re: diplomat 8332 dishwasher
don,t have a list of codes in front of me but if f1 is ntc , check to make sure u have no water in base where the ntc is , motors have been known to leak and spray the componets to give fake fault codes.
As post above says bayonet fitting in and turn.
if dw is under say 2-3 years ntc straight swap block connection
if dw over 2-3 years+ they have tags/spade on ntc either cut and join maybe in some cases it will change the temperature by joining wires by few degrees or follow to board and replace whole wireRe: Hygena AYH8101/2
my memory is faded on these been long time but also check the spray arm that the litte ridge are not worn out, so when u push it on it grips
Re: Diplomat AHY4310 not heating properly
hi i belive you need a new fan motor and i belive we talking about the main fan oven at bottom , also the stat maybe out of calibration or faulty so it saying 200c when is really 150 c but
If fan has stopped at all it will requies a new one and you will likely start getting strange noise soon , the stat sits above the fan so if the fan not working correctly stat is reaching heat to fast while rest of oven is not
If we talking about the top oven it don,t hav a fan but has a cooling fan above it.Re: Diplomat ADP 8242
2 types of leaks u can get on them door leak or base leak
if base leak 99/100 it
Will be the 2 washers on bottom of air break that is on right hand side , replace washers will be the cureRe: Diplomat APM8502 overfilling ! Help needed !
if we talking about the sump hose as linked in post above yes it sucks to do ,
A tip put hose in very hot water for few mins to soften it up some, that will help to place it in the hole at botton of machine, manufactures use a sealant golden colour u see remains of it on edge, most likely u won,t need to use any tho should be a good tight seal with out.
if the lips of seal are nice and neat and level and look right and it leaks u need to run some sealeant around it.
ps do a few boil washes help clean out the system and listen for heater to come in on programme 1 and 2 with temp set to 90{e5d1b7155a01ef1f3b9c9968eaba33524ee81600d00d4be2b4d93ac2e58cec2d} sometimes if element goes down can cause problems with blockagesRe: Diplomat ADP0150 oven not working
oldish post but u may read this im bored hehe
if cooking with 1 tray use the top 2 lines of the middle section in oven
1) have u just come from a electric oven to gas? can be a fairly large heat diffrence between bottom and top of oven.
2) check door is closing well still and you will lose some heat from the metal bar at top where seal is that is normalRe: Diplomat ADP5330 – Major Fan Noise
noisey cooling fan don,t allways mean its the fan but {e5d1b7155a01ef1f3b9c9968eaba33524ee81600d00d4be2b4d93ac2e58cec2d} is high, to see if its cleared it self or if its seized run oven for 10 mins tunn oven of if u hear blowing nosie its cleared its self if u hear nothing fan motor has seized ie new fan motor.
noise can be from
1) vibrating back panel on oven
2) insulaton iie tinfoil looking stuff come abit losse and rubbing fan or crap loads of gunf on fan blade or fan housing is not tighten up
cooling fan is run by a stat and will carry on after u turned oven of untill the thermal stat has cooled down.Re: Door on Diplomat ADP3640 not closing properly
99/100 it is normally the hinges, you will always get a slight bigger gap at top than u will at bottom of door part of the design, allso check that door seal is not warn out ie become very brittle or very weak.
hinges inside are a pain but are doable, my memory is faded here but i think keep a long screw driver through hinge housing at angle so hinge don,t drop down, i think there is small hole below housing hinge that u can slide it downif not will have to remove some screws from side to get ya fingers in there becarefull tho some of the screw holes and sides are machine cut and are very sharp, if able to slide hinge down important not to let it fall of screwdriver and use that it at angle to line it up to get screws back in or u will have to strip it down i would norm ally do with out removing oven from carcause. ps allways make sure oven is turned of at the mains before u do anythingRe: Hygena APP2410 cooker hood
There is no fuse as above post says but there is normally a fuse at the main connection ie on a plug in side hood cover or if wired to spur/switch to left or right of hob above the work units, somtimes builders put its above top units on some kind of connection.
If no fused plug or spur socket with fuse and it went bang and both bulbs went and now is dead as above post states it would of blown the tracking on the pcb and will require new pcb . always best to have those extractors fused on plug spur ect it will save a ton of hazzle.Re: Hood problems – Hygena APP2130
9 out of 10 brand new extractors will not be faulty when people think they have problems . most likely the wire/cord as been left to long or not been cliped up out the way and has fallen down and jammed the fan blade or a bit of plaster has fallen down or something along tho lines.
unlikey to be pcb , when u turn on and hear buzzing mean either the fan is stuck on somthing or motor is struggling ie bad motorRe: MFI DIPLOMAT OVEN
Any oven door glass can blow pot luck even if gone few times i have seen them go on diffrent ovens made by diffrent companies under the diplomat/hygena name, it is not a common problem at all, its just scares people when it happens.
Most likely nothing wrong with your oven, but if you are finding its is burning all your food get it checked out incase its over heating by (extracare engineer.)
