Forum Replies Created
-
Posts
-
Re: Hotpoint Twin Tub 9414
PMP17 from Qualtex probably your best bet?
I do have on chucking about in my garage somewhere if you’re stuck though
Re: CREDA W220VW CONTROL BOARD CONFIGURATION CODE
iadom wrote:I have a new one, issue Five, had it since beginning of September.
Ooooh does is Sir?….Is it good Sir?…..Ooooooh Issue 5 suits you sir!…… :rotfl:
Sorry but the Kenneths crack me up and couldn’t help that, I don’t know what came over me…sorry 😳
Re: zanuzzi fj1053
plumbob wrote:Can I order just the magnet, or the whole tacho assembly ?
Tacho comes as an assembly (Part No 50204873009) order via emailing these details to :
spares@ukwhitegoods.co.ukRe: Bosch SGS45E08 leaking to base
ajbaker wrote:Is there a quick description for getting the door spring tensioners back on?
Yes, with the door shut, simply lift the white plastic coupling with a pair of pliers back onto the hook of the hinges.
Your observation as to the leak sounds interesting and possibly simple to sort. Possible access to it via removal of the water inlet unit (on the l.h.s) may be required?
As to the 2 year guarantee bit boro mentioned, Bosch’s guarantee does not apply to a third party after all 😉
Re: Bosch dishwasher
bobokines wrote:Most Bosch parts are available from Connect Distribution.
Rip-off city there though Bob. Cut out the robbers and middlemen I say 😆
Re: Poor Wash Results
Oh yes…a perfect post Neptune being as many of us have taken advantage of the Detergent Training initiative so far!
http://www.ukwhitegoods.co.uk/modules.p … opic&t=106
Meanwhile, and to try answering your question, firstly the correct dosage is the primary factor. Secondly the correct programme selection relative to the type of garments being washed and thirdly care to avoid overloading.
Whites going grey is very often a result of one or all of the above not being applied. Whites also need a bleach based powder and especially a biological one at that.
I hope that helps? But I am sure our Technical Trainers can elaborate further should you wish more detailed info 😀
Re: update
gixerk1 wrote:after another wash the glasses are almost perfect rinseaid on three salt on 1
im still at a loss to know why this is i must have put about 1 kg of salt in could this have been the problem or has it recharged the softening processTim,
Bit difficult trying to translate what you are on about here?
But do please bear in mind that dishwashers do need salt in order for the water softener to function correctly. If you are using 3 in 1 tablets, you still do need to use the water softener and regularly put SALT in it!
Re: CREDA W220VW CONTROL BOARD CONFIGURATION CODE
Dave_Conway wrote:not to worry, another one is on the way
I’m sure if we ask Brian nicely, he will give us a UKW group discount on Partfinder 💡
I hope Dave Hazzard will post mine by return as its 4 days and counting since mine went belly-up and I cannot source the parts I need 🙁
(Why should that be anyway 🙄 )
Re: salt left on crockery
gixerk1 wrote:i could not see a softner on the neff schematics would you be able to tell me where it is located
Its the whole ‘Water Inlet Unit Part No: 208696 Cost =£128.08 + P & P 🙁
Re: Bosch dishwasher
tonyclifton wrote:were do get parts from and any idea of cost
Re: hotpoint WM62P
Not sure exactly what you mean but usually when an Interlock goes it blows the neutral return track on the module. Loosen the timer/module and have a squint there? At best you may get away with soldering the link back on the board, at worst?…New Timer/Module 🙁
Re: SGS45E08 leaking – connecting door tensioner again?!
ajbaker wrote:A quick 5 minute investiagtion revealed one or two parts with a minor drip during the drain cycle. While it looked as though it was the heater leaking
The minor drip?….Can you describe where you saw the leak?
Your machine is only 15 months old so it is unlikely the heater unit or motor are leaking but one never knows. A full strip-down to see may be the only action to be certain though. You are half-way there if you have the door off. Best give me a bell and for a modest extra fee I can check it out 🙂
Re: zan wjs 1265w not starting
Normally I would be certain the Interlock is at fault? Possibly I would try another? How long after you press ‘Start’ does it beep? ”Cos these machines ‘self check’ before starting and if say the valve or pump was open circuit, it would give an error like this. 😕 Worth a bit of a check around to see I reckon! 😉
