Forum Replies Created
-
Posts
-
Re: Extended guarantee schemes – your thoughts?
Domestic & General rule the roost on that front. And every single brand sold and guarantee registered then D&G are on to it. So, unless you wanna be a ‘service partner’ you’d be best to steer clear of offering warranty options in my opinion.
Re: NEFF 8406 Cycle never completes
DIYdisaster wrote:Yep. The abort empties the unit just fine.
That fact now rules out the drain pump. So the finger of blame lies with the thermostat on the top of the heater unit. Accessing that to replace it is simple enough but warrants a deal of surgery involving lying the machine on its back and removing the bottom inspection cover.
Re: NEFF 8406 Cycle never completes
DIYdisaster wrote:… and the pre-rinse completed OK.
Finally we have established that the pre-rinse cycle works normally.
That pretty well rules out the Control unit (which incidentally costs £81 and is part no: 00426436).
Next question: When it sticks and you feel the need to abort (reset) the cycle, does it pump out all the hot water OK?
Re: Levelling …how far do you go
cornwell40 wrote:It was to install afreestanding machine.
Seriously?
cornwell40 wrote:He did say that he’d had trouble when last one they had delivered and had to finish it off themselves. 😉
….to which you said “well crack on with that then sunshine”.
Re: Bosch SGS5002GB/07 timer stops/not heating
You refer to the safety overheat cutout and not the thermostat. That is located on the heater unit accessible after removing the RH side panel. Your machine does not have a PCB controller.
Re: Bosch SGS5002GB/07 timer stops/not heating
Yes the timer goes ‘on hold’ until the thermostat (thermistor in fact) on the heater unit allows the timer to continue through the cycle.
Re: Lamona oven gas smell
Ditto to my colleagues comments. Only a Gas Safe qualified person could possibly check and test your oven. DIY intervention dangerous in the extreme.
Re: Can it happen here ?
Why not start this then with an official petition 💡
https://petition.parliament.uk/help
(I’m sure a raft of excuses to this idea may follow but hey!)
Re: Lamona oven gas smell
Two facts stand out here. 1) That it’s been like it from new. 2) That it was converted from natural gas to LPG at that time. The combined conclusion has to be that the conversion wasn’t carried out correctly especially with reference to the main oven. Possibly the wrong gas nipple was used or the air ratio adjustment of the main oven burner set incorrectly. Or maybe even the regulator on the gas bottle is wrong or faulty?
That carbon monoxide alarm has done its job for sure though and you’re safe and well. Don’t use the oven now until it is sorted or disposed of. :plug:
Re: Neff Dishwasher S51E50X0GB Not Heating Water
95{e5d1b7155a01ef1f3b9c9968eaba33524ee81600d00d4be2b4d93ac2e58cec2d} sure the heater is the likely culprit. Inspecting the PCB is a simple task once the machine is fully pulled out. Removing the RH side panel will reveal it. The heater a little tricky to check it with a meter but removng the front plinth will allow access there.
If you have been using the machine all the while without salt thinking the 3 in 1 tablets cure all then for sure the heater is duff! 🙁
Re: Levelling …how far do you go
There’s two ways of looking at it….
1) Removing old integrated, supplying and installing a suitable replacement the customer would expect some degree of professional service that wouldn’t necessarily require their intervention. So no matter what the state of the walls, floor or kitchen furniture the installer would be expected to deal with it.
2) If the customer simply wants the appliance, they purchased elsewhere, to be installed and the location was found unsuitable then it is not unreasonable to suggest the problem is theirs to solve.
Re: Bosch SGS5002GB/07 timer stops/not heating
Looking on Bosch’s spare parts web site I see it listed as part no: 00165385. To confirm the heater works simply temporarily short out that safety stat. Though in my experience the heater itself being faulty the more usual case.
Re: Bosch washing machine new brushes fitted
The motor plug to PCB connector blocks are numbered albeit very tiny numbers that perhaps a magnifying glass would confirm.
Re: Electrolux EW1006F Randomly Stops
With all the follow-up information taken into account I still conclude that the 3 level pressure switch is the likely culprit.
