Martin114

Forum Replies Created

Viewing 15 posts - 241 through 255 (of 334 total)
1 2 3 … 16 17 18 … 21 22 23
  • Author
    Posts
  • August 24, 2007 at 1:55 pm in reply to: Proline TDV65 Tumble dryer spares #225609
    Martin114
    Participant

    Re: Proline TDV65 Tumble dryer spares

    Has it got twin jockey pulleys or just a single one?

    Connects number for the twin is 5031683019091

    August 24, 2007 at 11:56 am in reply to: Proline TDV65 Tumble dryer spares #225607
    Martin114
    Participant

    Re: Proline TDV65 Tumble dryer spares

    I think the machine may be a whirlpool with the belt being a 1970 H7 (or 1965 H6)

    August 23, 2007 at 10:35 pm in reply to: Fault Code Guide #223231
    Martin114
    Participant

    Re: Fault Code Guide

    Very useful Ken, trouble is the WIDL codes page is getting worn out :hmm:

    August 16, 2007 at 6:25 pm in reply to: Brandt? BDW060/A Askoll circ pump #224851
    Martin114
    Participant

    Re: Brandt? BDW060/A Askoll circ pump

    Thanks Chris.
    🙂

    August 11, 2007 at 10:12 pm in reply to: insulation test #224109
    Martin114
    Participant

    Re: insulation test

    I find low readings due to carbon dust around the brush holders.

    August 10, 2007 at 7:12 am in reply to: HOTPOINT FDW20P Module #224001
    Martin114
    Participant

    Re: HOTPOINT FDW20P Module

    should be a C00144314

    August 1, 2007 at 5:13 pm in reply to: Hotpoint WF840 #223083
    Martin114
    Participant

    Re: Hotpoint WF840

    Hi Tony, If the resitances are about the same I would see no reason why the spade type shouldn’t do the job. And probably more reliable with decent spade connectors rather than the flimsy idc plugs.

    July 31, 2007 at 9:48 am in reply to: INDESIT IDL530 #222990
    Martin114
    Participant

    Re: INDESIT IDL530

    Hi trainer,
    I had this problem before which was cured by replacing module with ntc attached.
    Cheers
    Martin

    July 29, 2007 at 11:13 am in reply to: sat nav #202788
    Martin114
    Participant

    Re: sat nav

    Dales-Electronic wrote:Would anyone be interested in bulk buying, (say ten) and splitting them around??

    That would be most generous 😀

    July 22, 2007 at 4:30 pm in reply to: Advice on Washer Dryer #221639
    Martin114
    Participant

    Re: Advice on Washer Dryer

    If the noise is there before the drum starts to turn, then I would say it’s very likely to be the drain pump worn. This is a very common fault and not expensive to fix.
    Unplug machine first if going in.

    July 17, 2007 at 5:57 pm in reply to: I’ve got a samsung fridge and its wonderfull!!! #221322
    Martin114
    Participant

    Re: I’ve got a samsung fridge and its wonderfull!!!

    Why just just here from Samsung users that are happy?
    💡 I know – what about happy indesit.co customers 😆

    July 14, 2007 at 10:28 pm in reply to: New 07 Reg. #221056
    Martin114
    Participant

    Re: New 07 Reg.

    kwatt wrote:At least I know now that at least one delivery went to plan, it appears another went wrong on Friday afternoon, of course Friday the 13th. 😕
    K.

    :waving:
    I also need 5+5 and 1+5 cards but I will see john on Wednesday so I will bother him with that :snigger:

    July 14, 2007 at 9:00 pm in reply to: New Cert. of Professional Competence for LGV Drivers #221048
    Martin114
    Participant

    Re: New Cert. of Professional Competence for LGV Drivers

    Hi Geoff,
    I think you can still drive a vehicle up to, but not exceeding 7.5 tonnes, with an ordinary car license.

    July 13, 2007 at 2:28 pm in reply to: Creda dryer getting too hot? #220445
    Martin114
    Participant

    Re: Creda dryer getting too hot?

    I have been to a similar machine where the whole cabinet was getting very hot and it turned out that the rear drum seal had at some time caught fire 😯 and the hot air was blowing past it :rolls:

    July 9, 2007 at 2:28 pm in reply to: ariston A1435s #220303
    Martin114
    Participant

    Re: ariston A1435s

    sounds like motor open circuit – check brushes – unplug machine before going in though.

  • Author
    Posts
Viewing 15 posts - 241 through 255 (of 334 total)
1 2 3 … 16 17 18 … 21 22 23