Micky 32

Forum Replies Created

Viewing 15 posts - 166 through 180 (of 279 total)
1 2 3 … 11 12 13 … 17 18 19
  • Author
    Posts
  • October 30, 2009 at 2:10 pm in reply to: Whirpool AWM 8000 headache #300816
    Micky 32
    Participant

    Re: Whirpool AWM 8000 headache

    Strange, she tried it again and ever since it has worked fine.

    October 3, 2009 at 10:36 pm in reply to: Zanussi ZT 685 #298545
    Micky 32
    Participant

    Re: Zanussi ZT 685

    I think it might be the 4th one, have to go back monday to look at the washing machine so will check then.

    September 16, 2009 at 7:22 pm in reply to: Hotpoint Indesyhte drum lifters #297147
    Micky 32
    Participant

    Maybe overloading?

    August 2, 2009 at 1:07 am in reply to: Bosch Classixx 1000 Express not always heating. #293483
    Micky 32
    Participant

    I have come across a couple with a dry solder joint on the relay.

    July 24, 2009 at 9:13 pm in reply to: Hotpoint CTD 80 #292965
    Micky 32
    Participant

    Re: Hotpoint CTD 80

    Oh this was a case the customer sticks the head in :rolls: , when i took the pump out he cleaned and dried out the fluff and water and probably threw away the rubber impeller, even so does it mean a new pump anyway if it comes off?

    July 24, 2009 at 4:44 pm in reply to: Hotpoint CTD 80 #292961
    Micky 32
    Participant

    Re: Hotpoint CTD 80

    Would you believe i got a call to a CTD 00 with the same symptoms today. Empty light on. This machine was built around May 2007. The pump for some reason isn’t pumping up the water even though it’s “working”. Looking at it when working you can see it’s not stable and vibrating. It seems to be a different pump from the earlier ones, are these giving problems? To me it looks like a cheaper pump.

    July 24, 2009 at 12:00 pm in reply to: Hotpoint CTD 80 #292959
    Micky 32
    Participant

    Re: Hotpoint CTD 80

    Thanks for all the replies lads. Went to it this morning and found the tray where the pump sits full of fluff, cleaned it out and it now pumps the water up to the top 😆 , is it normal for the rollers on the front to be noisy on these machines, it’s making a fair racket :rolls:

    July 23, 2009 at 3:07 pm in reply to: Hotpoint CTD 80 #292957
    Micky 32
    Participant

    Re: Hotpoint CTD 80

    iadom wrote:Sticking float switch or gunged up water container under pump a possibility.

    I have sent you some ‘stuff’. 😉

    Jim.

    Thank you for the “stuff” you sent, appreciated 😀

    June 5, 2009 at 9:30 am in reply to: Hotpoint WD420 #288565
    Micky 32
    Participant

    Re: Hotpoint WD420

    I have seen valves breakdown after a few seconds and then work again after a rest but as this is a WD i doubt it would be that simple 😮

    June 2, 2009 at 3:51 pm in reply to: Overheating AL 120 Hoover washing machine #288327
    Micky 32
    Participant

    Re: Overheating AL 120 Hoover washing machine

    Well this what greeted me when i took the lid of today. She had switched the washing machine on before going to bed and when she got up this morning the trip switch was down. They were lucky and have 5 young kids. As you can see the module went on fire, what could have caused this? Shorted motor, bad connection?

    May 28, 2009 at 2:04 am in reply to: FJS 1225w #287650
    Micky 32
    Participant

    Re: FJS 1225w

    Problem sorted, thanks for all the replies lads 🙂 It turned out the circulation pump open circuit. Replaced it and all is ok.

    May 23, 2009 at 10:31 am in reply to: FJS 1225w #287648
    Micky 32
    Participant

    Re: FJS 1225w

    Thanks 😀 After further reading on here, it seems when the pump goes it brings the pcb with it?? 😡

    May 22, 2009 at 10:04 pm in reply to: FJS 1225w #287645
    Micky 32
    Participant

    Re: FJS 1225w

    Also in diagnostic E 85 is coming up, not listed in the book.

    May 15, 2009 at 12:04 pm in reply to: Has qualtex inmproved on their bosch brushes? #286329
    Micky 32
    Participant

    Fitted another set yesterday. They fitted perfectly without having to file them and also silent on the spin.

    May 6, 2009 at 9:35 pm in reply to: Hotpoint stuck in spin. #285262
    Micky 32
    Participant

    Interesting. My next door neighbour has a WF type machine( didn’t look at the mod number) but has a didital display and tonight it was stuck on spin with a minute showing. I reset it and it worked ok. It happened once a few months ago also and when i reset it was ok until now.

    Iadom, can you send me some of that info please? email iguana30ie@hotmail.com

  • Author
    Posts
Viewing 15 posts - 166 through 180 (of 279 total)
1 2 3 … 11 12 13 … 17 18 19