Muv

Forum Replies Created

Viewing 15 posts - 391 through 405 (of 647 total)
1 2 3 … 26 27 28 … 42 43 44
  • Author
    Posts
  • November 15, 2012 at 2:49 pm in reply to: Hotpoint WD420 #384815
    Muv
    Participant

    Re: Hotpoint WD420

    Sorry , its the start and drying lights are flashing, not steady

    Martin

    November 15, 2012 at 10:24 am in reply to: Bosch Washing Machine not spining #384742
    Muv
    Participant

    Re: Bosch Washing Machine not spining

    Agree with Dr Drill completely

    Maybe worth checking the comdition of the commutator before fitting brushes as well..


    Martin

    November 14, 2012 at 3:57 pm in reply to: Bosch WM not starting #384769
    Muv
    Participant

    Re: Bosch WM not starting

    Quite possibly the motor brushes are worn, check these are ok..if not replace..
    If they are not worn,then more than likely a faulty door interlock

    Martin

    November 14, 2012 at 10:06 am in reply to: Bosch Washing Machine not spining #384739
    Muv
    Participant

    Re: Bosch Washing Machine not spining

    Sounds like the brushes are worn…especially if it spins without any problems without a load inside

    Martin

    November 11, 2012 at 6:57 pm in reply to: Diplomat APL 1722 cooker #384118
    Muv
    Participant

    Re: Diplomat APL 1722 cooker

    Just sent the pics

    Thanks
    Martin

    November 10, 2012 at 10:23 am in reply to: Hoover OPH616 water temperature #384518
    Muv
    Participant

    Re: Hoover OPH616 water temperature

    Hi

    Yes, thats the one you need..

    Martin

    November 9, 2012 at 4:41 pm in reply to: Diplomat APL 1722 cooker #384116
    Muv
    Participant

    Re: Diplomat APL 1722 cooker

    Can you confirm your email address for me please, as they keep coming back to me undelivered!

    Thanks
    Martin

    November 9, 2012 at 2:54 pm in reply to: Hoover OPH616 water temperature #384516
    Muv
    Participant

    Re: Hoover OPH616 water temperature

    Complete assembly is here

    http://shop.ukwhitegoods.co.uk/41021737 … ng-element

    Martin

    November 9, 2012 at 2:48 pm in reply to: Hoover OPH616 water temperature #384515
    Muv
    Participant

    Re: Hoover OPH616 water temperature

    Its the NTC “water temperature sensor” this is located in the element itself, and is a push in fit..with a plug type connector around £10 to purchase at most…..check connections on the element itself are nice and tight, and show no sighns of over heating…if they do then change complete assembly which will come with the NTC sensor fitted ready..

    Martin

    November 8, 2012 at 5:50 pm in reply to: Diplomat APL 1722 cooker #384115
    Muv
    Participant

    Re: Diplomat APL 1722 cooker

    Hi
    Have resent them, as they didnt seem to send properly

    Thanks
    Martin

    November 5, 2012 at 4:38 pm in reply to: New ATMs rollout #384233
    Muv
    Participant

    Re: New ATMs rollout

    Halifax machines being doing that for at least 10 years.. Cash or cheques… Tho not sure they do any business accounts!

    Martin

    November 5, 2012 at 12:36 pm in reply to: How do you remove the top of a Hotpoint tcm570p dryer #384173
    Muv
    Participant

    Re: How do you remove the top of a Hotpoint tcm570p dryer

    Been using the palms method for so long, it now hurts my arms doing that…
    So hammer or block of wood from now on! Lol

    Martin

    November 5, 2012 at 12:35 pm in reply to: Diplomat APL 1722 cooker #384114
    Muv
    Participant

    Re: Diplomat APL 1722 cooker

    Thanks
    Just sending them now

    Martin

    November 2, 2012 at 9:31 pm in reply to: How do you remove the top of a Hotpoint tcm570p dryer #384168
    Muv
    Participant

    Re: How do you remove the top of a Hotpoint tcm570p dryer

    They can be very tight!

    I usually remove tight tops using a rubber mallet, bang away at each front corner,..using short sharp blows…this usually shifts em!

    Dont lift the front, just remove the rear screws…and proceed as described..

    Hope it works for you!

    Martin

    November 2, 2012 at 5:27 pm in reply to: Miele w829 washing machine #383387
    Muv
    Participant

    Re: Miele w829 washing machine

    Update

    Miele now working again

    It was the contacts on the RK1 relay..welded together!
    also the radial fuse, was blown,both came out quite easily, with the aid of a solder sucker & some copper braid…

    Thanks to all contributions

    Martin

  • Author
    Posts
Viewing 15 posts - 391 through 405 (of 647 total)
1 2 3 … 26 27 28 … 42 43 44