Muv

Forum Replies Created

Viewing 15 posts - 61 through 75 (of 647 total)
1 2 3 4 5 6 … 42 43 44
  • Author
    Posts
  • January 15, 2015 at 12:59 pm in reply to: Indesit WIXL123 #423656
    Muv
    Participant

    Re: Indesit WIXL123

    Doh! Always forget about that thread… Thanks iadom

    January 15, 2015 at 12:25 pm in reply to: Hotpoint wmud962g not taking in water. #423642
    Muv
    Participant

    Re: Hotpoint wmud962g not taking in water.

    Are you sure the filter and pump housing are clear of debris? Try running machine on pump out eith the filter removed,and check the pump impellor is rotating..

    Martin

    December 16, 2014 at 10:37 pm in reply to: Miele Novatronic W827 not starting #422551
    Muv
    Participant

    Re: Miele Novatronic W827 not starting

    The loud bang was due to overloading the machine,and due to the age of the machine the shockers cant cope with the start of the spin cycle.
    The drum pulley hits the rear casing,causing the motor to stall just enough to blow components on the board..

    You need
    New brushes
    New shocks
    And the board repaired!

    PM me regarding the board repair..

    Ive done around 30 this year alone..

    Martin

    November 11, 2014 at 11:56 am in reply to: Miele Novotronic W833 #421329
    Muv
    Participant

    Re: Miele Novotronic W833

    It could be the pressure switch,or possibly a relay on the board!
    Also worth checking pressure chamber for blockages
    Martin

    September 17, 2014 at 6:09 pm in reply to: Miele W2104 washer troubleshooting #419279
    Muv
    Participant

    Re: Miele W2104 washer troubleshooting

    You could try unplugging from the mains for at least 24 hours then retry it!
    Sometimes works

    September 16, 2014 at 9:07 pm in reply to: Miele W2104 washer troubleshooting #419277
    Muv
    Participant

    Re: Miele W2104 washer troubleshooting

    It could be a faulty power switch or loose commections to it..
    Also this model is known for the main board transformer breaking down…
    The compant that makes the transormers are unable to sell them as they are made specifically for MIele… There is a guy that may be able to help you out
    Try here
    http://www.youfixit.eu/en/

    September 15, 2014 at 6:38 pm in reply to: Miele WT2670 F53 – Tacho Generator #419148
    Muv
    Participant

    Re: Miele WT2670 F53 – Tacho Generator

    I have a machine here that has the same motor, i will try and get it tested for you tommorow,..
    Please PM me with your mobile number, if you still want it

    September 13, 2014 at 7:45 am in reply to: Miele WT2670 F53 – Tacho Generator #419147
    Muv
    Participant

    Re: Miele WT2670 F53 – Tacho Generator

    Ok,will have a look for you,and see what i have

    September 12, 2014 at 11:40 am in reply to: Miele WT2670 F53 – Tacho Generator #419145
    Muv
    Participant

    Re: Miele WT2670 F53 – Tacho Generator

    Whats the motor number,i may have a few 2nd hand ones!

    September 3, 2014 at 9:00 pm in reply to: Kenwood KID60S10 heater replacement ? #418654
    Muv
    Participant

    Re: Kenwood KID60S10 heater replacement ?

    The genuine one will fit, will have the correct connector, and is probably just as cheap as any element that you will “bung” in!

    Other an those reasons, then doctored connections would have to be electrically sound, or they would cause problems later on!

    Hope this helps

    Martin

    September 3, 2014 at 8:47 pm in reply to: Hotpoint TC71 condenser dryer #418678
    Muv
    Participant

    Re: Hotpoint TC71 condenser dryer

    Its usually the timer at fault

    Martin

    September 2, 2014 at 11:24 pm in reply to: Kenwood KID60S10 heater replacement ? #418652
    Muv
    Participant

    Re: Kenwood KID60S10 heater replacement ?

    No! Get the genuine part.

    September 1, 2014 at 9:56 pm in reply to: Strange rotation problem #418560
    Muv
    Participant

    Re: Strange rotation problem

    Broken spider arm maybe gents?

    August 27, 2014 at 11:30 pm in reply to: Indesit is70c Fan Catching on rear cover? #418392
    Muv
    Participant

    Re: Indesit is70c Fan Catching on rear cover?

    Check the fan itself,it could be worn away in the centre due to overheating,or the shaft from tje motor could be rusted so badly that the fan is not fitting correctly.

    Martin

    August 27, 2014 at 8:01 am in reply to: Miele prestige plus 6 – keeps tripping our RCD please help!! #418330
    Muv
    Participant

    Re: Miele prestige plus 6 – keeps tripping our RCD please he

    Could you supply us with a side view of the unit you unplugged. And possibly a view of the whole top view of the machine?
    The heater relay is usually on tje right hand side, and is a orange/tan color plastic unit.
    Judging by the thickness of the black wires connected to it I’m almost certain its the heater relay

  • Author
    Posts
Viewing 15 posts - 61 through 75 (of 647 total)
1 2 3 4 5 6 … 42 43 44