nigegt

Forum Replies Created

Viewing 15 posts - 151 through 165 (of 420 total)
  • Author
    Posts
  • in reply to: Beko american #364960
    nigegt
    Participant

    Re: Beko american

    Yeah thats why i said maybe be just the lower vent block with ice. Quite a long evap in the freezer so it tends to do ok until it gets really frozen up when/if fan fails though.

    Nige

    in reply to: Samsung Oven Tech info #364730
    nigegt
    Participant

    Re: Samsung Oven Tech info

    It will prob be the cut out on top of the fan duct in the middle. By pass to check. It’s the only problem so far i’ve had with these and done quite a few. Must admit i did order a pcb first time though. Couldn’t see the woods for the trees lol!

    Nige

    in reply to: Beko american #364958
    nigegt
    Participant

    Re: Beko american

    Sounds like the ciculation fan in the top of the freezer has gone. All the cold air collects at the bottom and freezes up the btm of the fridge too. Or the top vent could just be frozen up. Nice easy job.

    Nige

    in reply to: The 0800 Thread #301782
    nigegt
    Participant

    Re: The 0800 Thread

    Now that is funny 😆

    in reply to: What’s the most stupid things customers say? #363865
    nigegt
    Participant

    Re: What’s the most stupid things customers say?

    No there is no model number on it anywhere…..

    My husband’s friend said it’s …………..

    Have you seen one of these before……….

    I’ve already taken it apart for you…….

    That’s a lot less than i thought…….

    How much!! You’re on a good thing aren’t you…

    in reply to: Novembers Claims #363545
    nigegt
    Participant

    Re: Novembers Claims

    It would be helpful if the job came through with the symptom code already in place please?

    Nige

    in reply to: Bosch Dishwasher filling problems #363167
    nigegt
    Participant

    Re: Bosch Dishwasher filling problems

    Sounds like the pipe from the matrix/pressure chamber into the dishwasher is still blocked so water is backing up as it’s filling and cutting off the flood protect switch.

    Look for a whiteish tube that goes round in front of the drain pump from the pressure chamber.

    Nige.

    in reply to: Beko wm5100 #363029
    nigegt
    Participant

    Re: Beko wm5100

    Brill! Many thanks!

    Nige

    in reply to: HOTPOINT HOB TOP #362734
    nigegt
    Participant

    Re: HOTPOINT HOB TOP

    Had same kinda thing yesterday. Landlord wanted three glass hob tops for HAE60P connect price £196.03 Each! Ordered from Hotpoint £82.32!

    in reply to: Miele Spare Parts #361806
    nigegt
    Participant

    Re: Miele Spare Parts

    Nice work 😀

    in reply to: whirlpool integrated dishwasher adg756 #362071
    nigegt
    Participant

    Re: whirlpool integrated dishwasher adg756

    I thought you’d taken up tree surgery steve? 😆

    Nige

    in reply to: whirlpool integrated dishwasher adg756 #362069
    nigegt
    Participant

    Re: whirlpool integrated dishwasher adg756

    The pressure switch/diaphragm thingy bob could be clogged. change that first and all will most likely be well.

    Nige

    in reply to: LG TDC70045E Drum Sometimes Not Turning #362167
    nigegt
    Participant

    Re: LG TDC70045E Drum Sometimes Not Turning

    Change the capacitor first this should clear your problem.

    Nige

    in reply to: Hotpoint rl88s freezing up #362341
    nigegt
    Participant

    Re: Hotpoint rl88s freezing up

    Yeah sounds like the thermostats bu66ered.

    Nige

    in reply to: ignis ADL 831 fills then drains #362398
    nigegt
    Participant

    Re: ignis ADL 831 fills then drains

    Sounds normal. just does this to make sure it’s washing in fresh water if been stood. Bit like when washers drain before door locking and filling or on servis when they fill for a while then drain and contiue to fill and wash.

    Nige

Viewing 15 posts - 151 through 165 (of 420 total)