Forum Replies Created
-
Posts
-
Re: Bosch WIS24141GB Bearings failed within 1 year
This isn’t a machine with the known bearing problem as it’s s split tub appliance . Out of interest , did you know what the fd number is/was?
Re: Neff dryer won’t start.
Also , if I remember correctly , the programme selection dorsal and the special program dials work separately. The special programs won’t work unless the programme selector dial is in the off position. By having the program in the 12 o’clock position , you should be able to select a special program and set the time accordingly……If that makes sense?
Re: Neff dryer won’t start.
If it doesn’t start but still counts down then it’s probably the door lock.
Re: SIEMENS SN26M253GB/55 WIRING ISSUE
Was it a heat pump that you replaced? The small plug wroth 3 grey wires on the side is the NTC connector so the worst you’ll get is an e11 error code.
Re: Bosch WAB28162GB/01
Normally the customer starting the machine with the door open (E16 = door open/faulty door lock) I think on this model it’s hold start button and turn selector switch one click anti clockwise. Turn selector back to 0 and it should clear fault.
Re: bosch sms40c32gb "refil salt light"
Give the salt a good stir with the handle of a wooden spoon . The salt may have bridged over the sensor
Re: bosch WAP28360GB/23
It could be the child lock has been inadvertently operated. Can’t be 100{e5d1b7155a01ef1f3b9c9968eaba33524ee81600d00d4be2b4d93ac2e58cec2d} sure without the instructions in front of me but I think you have to make sure it’s on the programme that was selected when the child lock was switched on when you try and disengage it.
Re: bosch tuble dryer with condensor led on display
Isn’t the WTW model a heat pump dryer ? If it is then they don’t get particularly hot anyways. The quick way to clean out the sump/drain pump area is to remove the pump itself then squirt lots of hot water back into the sump area before syringing out. Best to keep going until the water comes back out clear. Its not always successful but an easier attempt than the strip down sometimes required.
Re: Bosch V6320X0GB/02 E13error
E13 is a door lock error……However , there are 3 possible caused .
Faulty door lock
Low insulation on dryer heater
Faulty component on control module.Unfortunately , it’s not that easy to identify which one is the source of the fault. Measuring the insulation on the dryer heater will either confirm or rule out that.
Then it’s 50/50 but the price of the board is hefty !Re: Changing water pipe on side by side fridge
The new style of BSH side by sides do have a replaceable water pipe.
Re: Changing water pipe on side by side fridge
I don’t think you can replace the hose separately so it’s a complete door job unfortunately .
Re: neff s54e53x0gb/10 dead
Also check the 4/5 triacs grouped together on the control module. If there’s any damage to any of their ‘tops’ , you’ll need to find our what it controls to trace the actual faulty component.
Re: Bosch dryers damp on autodry
Ask the customer to remove the load , stack and leave for 30mins……then feel it again. It’s one of the recommended practices after using a Bosch dryer
Re: Bosch dishwasher S41E50N0gb Noisy wash
Depends if it is a continuous noise or an intermittent ‘groaning’ noise . I.E occurs every 2 minutes. I’ve yet to change a diverter for noise. However , the top spay arm system can ‘groan’ every couple of minutes for a few seconds as the flow changes between spray arms. It’s caused by the connection of the top spray arm at the rear letting air out……a bit like the neck of a balloon. It can also be caused by the top basket being wonky. Normally , with this noise , replacing the top spray arm system works.
