Forum Replies Created
-
Posts
-
Re: Baumatic B180 SS B
Interesting Bryan – If you bang in B180 on their search facility, it goes to that motor. However, it does not have the three long legs on the front, so I doubt that it’ll fit. Thanks for the try though 😀 .
Chris.
Re: Terim Spares
Bulb is here:
http://www.ukwhitegoods.co.uk/modules.p … cts_id=166
Knob is p/no 414206 – email to spares@ukwhitegoods.co.uk for ordering.
Regards,
Penguin45.Re: Indesit WD10 13 Flashes
It’s a problem with the dryer temperature control circuit. Click the link below for pro help, power off if investigating.
Regards,
Penguin45.Re: whirlpool adg7340 hose clips
The clip for the pump inlet is replaced by a slimline jubilee clip p/no 4812 401 18157 – about a fiver 😯 IIRC.
spares@ukwhitegoods.co.uk will get you one……..
Suggest you counter with taxi fares for school run.
Regards,
Pengun45.Re: Candy CIC60 Reverse Action Tumble Dryer
Safety cut-out will have failed – not a service part, so you need this:
http://www.ukwhitegoods.co.uk/modules.p … cts_id=333
Regards,
Penguin45.Re: proline electric oven problem!
This is a Brandt made oven – element is p/no 76×3719, scary expensive – there is an alternative, HM14103 at a much more acceptable price – email to spares@ukwhitegoods.co.uk for pricing and ordering.
Regards,
Penguin45.Re: Dead WFL2260 after changing brushes
Your other thread states:
“I’ve got the motor out of my Bosch with a view to replacing the brushes (drum won’t budge & open circuit measured across the brushes).”
What are we supposed to make of it? Get the motor meggered for earth leakage, be prepared to be amazed at the price of motor and module repalcement.
Penguin45.
Re: Dead WFL2260 after changing brushes
It’s so much easier when you keep it all in one thread…………
I note in your other thread that the drum won’t budge. Assuming that this has locked the motor it has probably cooked the armature. If you megger it, you probably find that the armature is leaking to earth – this will cook the control board.
Regards,
Penguin45.Re: Candy Forma CDW 250 stuck on drain
It is possibly flooded in the undertray and the flood protection system has activated, holding the drain pum on. With the power off, drain undertray, find leak.
If you’re not sure how to proceed, click the link below for a UKW engineer.
Regards,
Penguin45.Re: Ariston A1535 burnt my clothes!!!
How can I put it to you gently? Flick back through this forum and there are countless posts relating to Ariston 2000, A series and Indesit W series machines (they are all the same basic appliance). This suggests that the machines are problematic to say the very least.
Noises on spin – things trapped between the drums, heater broken off bracket, drum support arm failed, bearings failing, concrete weight (front or top) coming away, suspension leg broken/failed/ripped through floor fof chassis, inner drum burst – shall I continue? Trouble is any and all of these are common failings on a machine which is cost engineered down to the fraction of a penny. The 1500 spin is also totally excessive – it gains very little in terms of drying (there is no actual need to exceed 1200), but the already marginal components get pounded that much harder. And fail faster.
If you want to persevere with this one, it’s probably time for pro help – click the link below for a repairer in your area.
If you’re giving up, the Bosch 1200 is generally available for under £300 and is a very adequate machine. Failing that hang on a month and the very splendid ISE machine will be available from this very site.
Regards,
Penguin45.Re: Hotpoint WM series
The computer side of things will only make a finite number of attempts to run the motor before giving up. I find the dial usually gets to just before the end of the ash on cottons.
Chris.
Re: Hotpoint BCI45 Slimline Dishwasher
Programme card is p/no C00086607 – email with number to spares@ukwhitegoods.co.uk for prices and ordering.
Be certain that this is what you want – it’ll be over £70……..
Regards,
Penguin45.Re: Hotpoint Multifunction Oven SY51
Inner door and glass assembly – p/no C00081603. Email to spares@ukwhitegoods.co.uk for prices and ordering.
Regards,
Penguin45.Re: Whirlpool washer dryer AGW338 Problems
AWG338? Merloni built washerdryer – induction motor, so drive belt slack is most likely cause of the fault. There are no brushes on this machine.
Power off if investigating………
Regards,
Penguin45.
