Seamy

Forum Replies Created

Viewing 15 posts - 2,056 through 2,070 (of 2,653 total)
  • Author
    Posts
  • in reply to: Miele W864 FL elemnt O/C #268816
    Seamy
    Participant

    Re: Miele W864 FL elemnt O/C

    Can’t pressure system can be re calibrated in servie mode?

    in reply to: Hotpoint cooker #268279
    Seamy
    Participant

    Re: hopoint cooker

    Very common problem on these type of machines with built in sw & t’stat , coming on when the should be off

    in reply to: MIELE NOVOTRONIC T220 TUMBLE DRYER NO HEAT #268347
    Seamy
    Participant

    Re: MIELE NOVOTRONIC T220 TUMBLE DRYER NO HEAT

    Try it on “timed drying” program. All other programs are sensor dry & heater will not be engaged if wet clothes are not sensed in drum.
    Paddles in drum are used to sense resistance between them & drum. If you take off top you will see a slip-ring with carbon brushes runnning on it which make up the sensing circuit.

    in reply to: Whirlpool American F’F display problem #267733
    Seamy
    Participant

    Re: Whirlpool American F’F display problem

    any idea of part num, please

    ta

    in reply to: Miele dishwasher filter required #260022
    Seamy
    Participant

    Re: Miele dishwasher filter required

    Should come separately

    Google Nettoparts for Miele spares or Miele UK

    in reply to: Miele Dishwasher went bang and then a rattling noise #267487
    Seamy
    Participant

    Re: Miele Dishwasher went bang and then a rattling noise

    Have Miele already looked at it to establish that the circulation pump motor is gone? It may be simply that something was caught up in it.

    Google Nettoparts for Miele spares prices.

    in reply to: miele premier novo washing machine fault. #265807
    Seamy
    Participant

    Re: miele premier novo washing machine fault.

    Theres a thermal overload built in to the motor, may be a good idea to check if its open circuit, whats the fault that comes up on the machine?

    Rinse light flashing denotes no motor action, or no feedback from tacho.

    in reply to: Beko wma 10 w overheating #267621
    Seamy
    Participant

    Re: Beko wma 10 w overheating

    Had board faults causing no heating.

    in reply to: re Belling Halogen inner element not working #267695
    Seamy
    Participant

    Re: re Belling Halogen inner element not working

    Need to leave it on for quite a while, Halogen lamp outer lights immediately but inner radiant coil takes longer to get red and is very hard to see with the bright outer ring. You sure regulator was wired correctly? What type of regulator have you fitted?

    in reply to: Miele dryer crease guard #267626
    Seamy
    Participant

    Re: Miele dryer crease guard

    CreaseGuard normally comes on after the end of every cycle, machine will tumble once a minute or so.
    There is a circuit diagram in the machine to help you trace any problems.

    in reply to: Beko wma 10 w overheating #267619
    Seamy
    Participant

    Re: Beko wma 10 w overheating

    Thermistor

    in reply to: Lux Cooker EKT6045X #267314
    Seamy
    Participant

    Re: Lux Cooker EKT6045X

    e-mail sent

    in reply to: BEKO WMA 510W Slow Programs #267015
    Seamy
    Participant

    Re: BEKO WMA 510W Slow Programs

    Had 1 or 2 of these not heating, usually a new board & NTC cured it.

    in reply to: MIELE FRIDGE FREEZER – KFN8462S – F2 FAULT CODE? #266847
    Seamy
    Participant

    Re: MIELE FRIDGE FREEZER – KFN8462S – F2 FAULT CODE?

    Most likely culprits are NTCs in Miele F/Freezers

    in reply to: Zan and Bendix wiring #266380
    Seamy
    Participant

    Re: Zan and Bendix wiring

    Need PNC number i’d think to be certain of correct one

Viewing 15 posts - 2,056 through 2,070 (of 2,653 total)