Forum Replies Created
-
Posts
-
Re: AEG oko lavamat 6200 non-draining soap tray
There should be a few tubes below syphon that cap fits over when in place, make sure these are clean, you can try pushing something flexible through to clean, around base of soapbox also.
Its a really small & simple thing to sort, would’nt go replacing the appliance over this yet.Re: Miele Novotronic W828 "main wash" light flashing
NTC = Negative temperature coefficient (the resistance decreases with increasing temperature)
Resistance of element should be approx’ 30 ohms, obviously it will vary dependant on wattage of said element.
2kw element should read 28.8 ohmsRe: Miele Novotronic W828 "main wash" light flashing
F8=
Main Wash flashing
Heating error, check heater, NTC, heater relay, connections etcOpen or short circuit in the NTC temperature sensor or its connections.
Re: Panasonic NA-127VB4
Any fault code come up at the end of the cycle?
From your description it sounds as its trying to drain but is blocked, the hissing noise you describe was likely the air/suction caused by the drain pump. (Even if water is below drum level some may remain in sump)
On some of these there is a non return valve which consists of a ball in the sump hose, if it sticks in up position it can cause the problem you describe, other Panasonic machines have a motorised valve which lets water down to drain pump. They would normally not advance on to spin until it has registered that water is all gone.
Hope this is of some help.(Humour welcome)
Re: AEG oko lavamat 6200 non-draining soap tray
Is it just the conditioner section of the drawer that has water,if so itslikely the little syphon is not oncorrectly, if the water from drawer is not going through to drum it could be the hose is twisted/kinked for instance.
Re: Miele dishwasher filling fault
Check seating of flowmeter, the flowmeter sometimes is too far away from the wheel to pick up the signal, also check cable connections at flowmeter & p.c.b
Re: Zanussi ZKT6050W and RCD
Check the polarity of supply to the oven, have found it to cause similar problems in past, but its mostly a heater low to earth that woul cause this.
Re: Beko washing machine heater fault
Poor quality elements i’d imagine, get nickel coated ones, they are very silvery looking, not dull grey.
Part number for a harsh water nickel coated element used by ‘Lux is 1326475207, think this will fit a beko too.Re: Zanussi ZWD 1271 W (washer-dryer)
Count the blinks & report back, dryer heater going low to earth is a common problem on these.
Re: Drum stopped turning – after replacing brushes
Maybe the brushes are tight in the holders and making poor contact.
Re: Blocked dishwasher pump
You have’nt included the said photo. You haven’t even included the model number of the appliance.
But i’ll try to help explain in the simplest terms possible, there should be 2 hoses connected to the appliance, a fill hose which is connected to a tap and the one you need to be looking for is a corrugated hose pipe from the appliance that goes to your drain, the pump is connected to the end of the hose in the machine. Careful working on the appliance, POWER OFF & watch out for sharp edges etcRe: 9v at compressor – pcb failure ?
Not certain about this model as I don’t work on Samsung products, but some fridge freezers now have inverter driven speed controlled compressors which adjusts the output, so voltage varies.
Re: Miele W460S trips RCD only on wash cycle
Heater relay perhaps? Have a look at the little motor that drives the water diverter on the soap dispenser it would have to run to a position if hot wash is selected and may be causing tripping, most times its a heating element though, quick test would be to disconnect cable off element tape up & see if it still trips.
