Forum Replies Created
-
Posts
-
Re: DRCS 68W condensing drier
As its a sensor dryer it will need damp clothes in drum to run on auto’ programme, if none are detected it assumes clothes are dry & plays a happy melody to tell you its finished. Timed drying should heat without regard for sensor which is located inside bottom of door. Clean Filter & Water Tank Full comes on at end of every cycle as a reminder to customer.
Re: BEKO DRCS76B 7KG CONDENSER
Normally if the felt has gone it leaves a nasty sticky residue on the front of drum, also if it has cut through the bearing slides theres plastic burn’t onto drum lip. If this is not removed or cleaned off the drum, it will catch on new felt & break belts again. New appliances now have a sewn joint in the felt & a more rounded front edge on drum, the belt has a tensioner on motor to prevent snapping belts.
Re: Too cheap Machines. scam
Its a SCAM, they have an address listed in Belfast (25 TALBOT STREET BELFAST) its been in the press & local news over here, as the business centre who have the property for rent have never heard of the Company using their address illegally.
IF IT LOOKS TOO GOOD TO BE TRUE IT VERY PROBABLY IS TOO GOOD TO BE TRUERe: Beko s512w cooker
Top element listed as 800W, lower 1100W, grill 1500W, take it from that that outer grill is only used during oven function. I’ve come aacross this problem before & all you can do is advise customer to preheat oven until oven light goes out before putting in food & calculating cooking time, they’ve probably been used to a fan oven before.
Re: Zanussi D/W no heat
Think its normally relay trouble on the P.C.B, if you’re handy with a soldering iron you could take board away & get a relay to suit.
Re: z1920-8ff
Think that part screws up through hinge into bottom of door. Likely bottom of door is damaged/broken, or just may have worked loose if you’re lucky.
Re: Beko baffler???
Motor tacho magnet needs to be checked for cracking, which you say is o.k, have replaced P.C.Bs causing this problem several times. No idea why they fail though.
Re: miele G977 plus dishwasher
Check non return valve of drain pump, details in your instruction book of how to do this. Instruction manual online if you’ve lost it.
Re: miele 646sci plus.
Likely a blocked impellor of the circulation pump motor, the appliance looks for a pressure switch mounted on the said motor to be activated, if it isn’t it goes into fault mode, starts & stops motor several times to try & clear any blocage.
Re: Electrolux ESL 6114 cycle never ends
Likely it’s not heating & running all the time expecting thermostat to be activated to move on.
Re: T/Bendix DH086 dishwasher, top spray arm.
Most likely the top basket is not going back in correctly, think from memory there’s 2 positions for basket level. If you have a look you’ll know what I mean, if it’s not seated correctly water won’t go in to top spray arm & no wash from top.
Re: Aeg Dishwasher door popping open
Door seal or bottom seal may be swollen, I’ve replaced both seals which cured problem on A.E.G dishwasher previously. But you need to inspect hinges also, if excessive load was applied to open door, like a child standing on it for instance it may push hinge in too far & cause it to be too tight at bottom, it would take very little to force it open.
Re: stoves 900ef 059040439 cooling fan motor
or this fan ?
http://shop.ukwhitegoods.co.uk/Cooker+{e5d1b7155a01ef1f3b9c9968eaba33524ee81600d00d4be2b4d93ac2e58cec2d} … Motor.htmlRe: Miele G1270 Dishwasher F14 pulsing problem
F14, Water intake fault.Heater pressure switch not activated.
The program is interrupted and the drain pump is operated. The display shows the message Technical fault code F14 – Call Service Dept. The buzzer is activated for 2 minutes. With the circulation pump operating after a water intake step, the heater pressure switch is checked to ensure that sufficient water pressure exists in the wash water circuit. For this the heater relay must have been activated.
Cause:
Heater pressure switch B1/13 defective.Remedy:
1. Check the heater pressure switch.
2. Check the connection plug and wiring harness.
3. Replace the heater pressure switch, if necessary.Cause:
Circulation pump inoperative. Circulation pressure too low (no pressure at heater pressure switch). Pump may be blocked by foreign objects.Remedy:
1. Check the circulation pump for foreign objects.
2. Check the circulation pump capacitor.
3. Replace the circulation pump, if necessary.Cause:
Foreign objects in heater pressure switch.Remedy:
Replace the heater pressure switch.Cause:
Flow meter B3/4 defective (incorrect water quantity registered).Remedy:
1. Check that the plate with the reed switch on flow meter B3/4 is seated correctly.
2. Check that the reed switch connection plug is seated correctly.
3. Replace the reed switch, if necessary.
4. Check the control lead from the electronic to flow meter B3/4.
5. Remove the water inlet mixer and replace if necessary.Cause:
Circulation pump defective.Remedy:
1. Check the circulation pump power supply.
2. Check the circulation pump capacitor.
3. Replace the circulation pump.Cause:
Circulation pump winding overheated; winding protection has cut out.Remedy:
Replace the circulation pump.Cause:
After a water intake step, heater pressure switch B1/13 has not opened switching steps 11–12 and 21–22. This starts the anti-stiction routine.Remedy:
Replace the heater pressure switch.Cause:
Motor capacitor defective.Remedy:
Check the motor capacitor and replace it if necessary.Cause:
Contacts on heater pressure switch B1/13 short-circuited. Contamination on the plug of the heater wiring harness and a conductive connection between the plugs and the main harness causes a short circuit to the contacts.Remedy:
1. Replace the heater wiring harness.
2. Replace heater pressure switch B1/13.
3. Reconnect the two individual plugs from the main harness (AMP 6.3 x 0.8 ) and apply new insulation sleeves. Do not interchange the plugs.
