Forum Replies Created
-
Posts
-
Re: AEG/Lux L64810 914524150 00 Sticks On Cycle
Have you accessed the diagnostic & if so was there any fault codes?
Re: Tom Tom gone.
I believe you can buy an external ariel or your TOMTOM which boosts the signal. Check out their website as I would think it’ll be there.
Re: **KNOWN ERROR CODES**
Beko Condenser & vented dryer Service program:
Plug the electrical connection and be sure dryer is working properly.Turn on dryer.Press “Start / Stop” button for a while and restart program.Than cancel the programme by pressing “Start / Stop” buton 3 sec.Turn off dryer.
2. Adjust the rotary switch to the Delicate program clockwise direction after Cottons programmes.
3. By pressing Buzzer Cancel function button turn on dryer.Wait until “Start / Stop” led is blinking.
4. Press “Start / Stop” button to follow steps of service program:
1. All led is blinking.
2. Controlling leds. All the leds are on and blinking.
3. Motor is turning anti-clockwise direction.
4. While motor is turning first level of heater is on. 1400 W ( 7 A) and pump is on, if exist.
5. While motor is turning second level of heater is on. 2000 W (9,6 A) and pump is on, if exist.
6. Motor is stopping. Heaters are off.
7. Motor is turning clockwise direction.
Continuing pressing “Start / Stop” repeats steps 1 to 7.Re: Zanussi FL1085 washing machine not heating up
Well, it soungs like you may have a timer fault there. If so, this could now be getting a little pricey. Either that or you have wired it up wrong somehow.
Re: Zanussi FL1085 washing machine not heating up
Hi.
There should be some resistance across the NTC sensor. If not, that could very well be the problem although I would also suggest you check the air chamber.
Re: Zanussi zwf12070w1 module fault?
Hi Allan.
Yes, sounds to me if you cannot enter diagnostic that the control board is toast.
Re: Beko Condensor Dryer/Hand Shredder DRCS65w H
Do you mean a DRCS68W? If so, it should be just a question of removing the access panel on the rear lower right side, removing the hoses & unclipping the pump cover. I have not had any trouble particularly doing this. Usually an easy job to be honest.
Re: beko DW450 slimline built in not draining
Hi.
If it is only 6 months old, contact your local Beko service agent, most if not all area’s of the UK use Serviceforce for this.
Re: e/lux esl642 pnc 911841062
Hi Franz.
The antioverflow valve is locking out. This is most likely due to The IWMS being bunged up which causes it to overfill. Take of the left hand side panel as you look at the machine from the front, if there is a load of crud in the large clear plastic chamber under that panel, bingo.
My advice would then be to change the IWMS (PtNo:1524624036) & just in case the pressostat (PtNo:1529900605).
Job done!
Re: zanussi ZWF 14791W won’t fill
Hi.
If the water fill was the issue, you would have an E10 fault code displayed. As you have not mentioned this I can only assume this is not the case. The valve is most likely OK.
Any other information on the fault?
Re: AEG competence fan rattle
The fan nut is a left hand thread so you would turn the nut clockwise to slacken & anti-clockwise to tighten.
Re: Zanussi FLE1215W Washer – 3 beeps but no action
3 beeps/flashes of end of cycle LED are a pressure system circuit fault. Things to check are: Mechanical/analogic pressostats, air chamber & air hoses, sump hose, drain filter, wash heater, main board, wiring to all electrical components I have just listed.
EWM1000 & EWM2000 fault codes are more or less the same.
