Forum Replies Created
-
Posts
-
Re: Neff Dishwasher can’t set programme
Thanks Martin,
I can’t see it being anything else really so I will replacing the board.Re: LG F1443.KD Poss PCB fault after short circuit element.
In case anyone else has this problem the short curcuit element also damaged the PCB.
Main PCB now replaced and machine working.Re: Zanussi ZDF221S Dishwasher Fill, heat, drain cycle.
Pressure switch tube was clear.
I wasn’t aware of the problem with the float switch, I will check that out.
Thanks Seamy.
Re: Bosch WET2820GB/13 stops mid cycle
How do I get into the diagnostics/last fault code on this machine?
Re: Bosch WET2820GB/13 stops mid cycle
I had considered the pressure switch but disregarded it as the machine continued after turning off then back on, would you agree with this or do you think it still a possibility?
If not it looks like the PCB.Re: Ikea Renlig DWT160 Underfilling
The pressure hoses and tubes are clear. As far as I can tell the pressure chamber is clear but this is difficult to tell as it is part of the sump.
r600a
These are the images of the dishwasher.
Not sure if the images are viewable if not they are here:
https://www.dropbox.com/s/0fhfbyzz1u9rvmv/2015-01-31{e5d1b7155a01ef1f3b9c9968eaba33524ee81600d00d4be2b4d93ac2e58cec2d}2010.24.40.jpg?dl=0
https://www.dropbox.com/s/wfdog45ehkbe8fd/2015-01-31{e5d1b7155a01ef1f3b9c9968eaba33524ee81600d00d4be2b4d93ac2e58cec2d}2010.25.20.jpg?dl=0
https://www.dropbox.com/s/dovtm9szatwbq79/2015-01-31{e5d1b7155a01ef1f3b9c9968eaba33524ee81600d00d4be2b4d93ac2e58cec2d}2010.25.35.jpg?dl=0
https://www.dropbox.com/s/mqfi083pvbusqxq/2015-01-31{e5d1b7155a01ef1f3b9c9968eaba33524ee81600d00d4be2b4d93ac2e58cec2d}2010.25.47.jpg?dl=0Re: Ikea Renlig DWT160 Underfilling
Hi r600a, I missed your post as the ukwhitegoods notifications have started to go to my spam folder.
I will try and get a photo later.Keith.
Re: Coffee machine touchscreen repair
Apparently this is a common problem with this machine.
I found a bit of information on cleaning a capacitive touch screen which involved using window cleaner on a bit of toilet paper to clean the surface.
For the sake of £200 I had nothing to lose so gave it a try.
So Mr Muscle window cleaner, a good clean then dry and so far so good.
As an appliance that is used in kitchen users hands are going to leave deposits on the surface and this I guess could cause problems.I’m just keeping my fingers crossed and money in the bank for now.
Re: Ikea Renlig DWT160 Underfilling
Having increased the water level manually, the wash pressure increases to what I would expect so it looks as if it is caused by the fill level.
The PCB has not been changed so no reason to suspect that at the moment.
The water level looks as if it’s controlled by a pressure switch. The fill is very slow but if too slow I would have thought I would get an error.
I can’t find a blockage but unable to be certain as the pressure chamber is built into the sump.
Are there any known issues with the pressure chambers or switches on these?
Does anyone have any other ideas what could cause this to under-fill?Re: Nefff Oven GB.1057-73LHCS Door springs
Thanks for taking the time to look into this,
Much appreciated.Keith.
Re: Ikea Renlig DWT160 Underfilling
OK, thanks for the information eastmark.
I think I will have to add a bit more water to increase the fill level a bit and see if the water pressure from the pump improves.
At least this will indicate if it is a fill level or wash pump problem.Re: Hotpoint HULT843P.UK Dispenser leaking
I explained that to her from the outset but having said that if genuine parts are used and everything put back as it should be then Hotpoint are not going to know unless they can go back to her original phone call and question how it was repaired.
Is this is a known problem on new machines and has part has been modified?
Re: Hotpoint HULT843P.UK Dispenser leaking
I agree but she called them and the person who took the call was rude and only interested in selling an extended warranty. Hotpoint will take over a week to attend the call so she would rather pay to have it repaired.
I have explained that this could be a design fault and if I change the dispenser body and hopper I can’t guarantee it will resolve the matter.
She still wants me to do the repair not Hotpoint.
