[washermanuk]

Re: Miele T650C Tumble Dryer

One thing i would check which is very common on this model is the cooling fan motor mounted at bottom!! this gets damp from condensation,due 2 the condenser seals not sealing.
try drying motor out with hair dryer or temp disconnect it then run machine again
hope this helps?

[washermanuk]

Re: MIELE CVA-620-1 coffee machine problem

No Indication in Display (Display Fields Are Black) Temperature sensor at steam through-flow heater is not connected correctly.
Temperature sensor at steam through-flow heater is open-circuited.
all i could find about display? 😥
Sounds like a display module fault?

[washermanuk]

Re: Miele G307i Spray arm retainer nut question.

Hi matey you can change the part without pulling dishwasher out
hope this helps

[washermanuk]

Re: miele g7859

found more lol 😉
After water intake, the heating level switch must switch. The query occurs 2 seconds over a length of 2 seconds in the following step. For target water measurements less than or equal to 1.1 gallons (4 liters) this fault monitoring is not active.
Cause
Heating level switch defective.
Remedy
Test the function of the circulation pump. See Service Mode 2, Description of Program Levels S21 to S24.
Check the connection plugs and wires.
Check the switch point of the heating level switch (2 seconds after circulation pump starts at nominal speed).
Check the connection hose to the circulation pump for obstructions.

[washermanuk]

Re: miele g7859

Hi matey fault is Heating Level Switch defective! Does Not Switch On Heating level switch does not react to water pressure.
Thick foaming cleaning or rinse agents in the waste water. This diminishes the waste-water pressure of the circulation pump at the heating level switch. . :rolls:
all i could find hope it helps Brian

[washermanuk]

Re: miele kfn8452sd

Hi matey send me your email address and ill try and send you a diagram?

[washermanuk]

Re: miele disdhwasher

worth checking heater relay matey

[washermanuk]

Re: Replacing bearings on Miele W919

Hi matey it is possible to remove the bearing spyder! Miele chaps use a special A frame to remove the drum from the casing…
Can be done without doing this by laying machine on its front but its not for the faint hearted as access is difficult to bolts!!
best way is to remove drum from the cabinet but get help very heavy!!!
Hard to give you precise instructions on removal? but if your a good engineer just do it step by step making lots of notes and pictures!!!
the bearing kit comes with all you need new bolts, grease etc part no#3589002
hope this helps Brian….

[washermanuk]

Re: Miele G653SCVI Plus (27/64298268) Dishwasher

sounds like the aquastop matey? have you checked valve with a meter?
you can do this underneath machine thin black cable with small plug on the end with brown and blue wires!!! or the float microswitch might be worth checking? get a few burnt out ones!!!
hope this helps Brian

[washermanuk]

Re: Christmas Greetings!!

MERRY CRIMBO PEEPS 😀 !!!

[washermanuk]

Re: Happy Christmas

Yes MERRY XMAS CHAPS!!!! :colour: THANKS FOR THE HELP

[washermanuk]

Re: Miele WT2670

Hi Matey are there any fault codes coming up on display?
Just had a thought tho!!! did you run machine on cottons wash and calibrate the load sensor?

[washermanuk]

Re: Miele washing machine

did you sort it matey?

[washermanuk]

Re: Capacitors

for smoothing matey due to the electronics on the boards 😉

[washermanuk]

Re: Miele Novatronic W340 overfilling

Hi matey it could be pressure switch out of calibration? its part of the 5338845 Power-/Control unit EDPL 106 220-240V Was told by Miele tech never to blow down the pressure pipe with it still connected to the board as this knackers the switch just a warning there 😉
Also i do get alot of probs with the motorised disp top 5492170 Wat.path cont.un. Detg.disp.top 220-240v the gears go out of sync this can cause weird faults on filling? just check its filling into the correct drawers or a horrible noise like plastic gears slipping? hope this helps Brian

[Author]

Posts