[clyde]

Re: Indesit DI 67

It sounds like the anti flood switch has been activated, your dishwasher may have a leak or may have overfilled – have a read through the other indesit posts in this forum this is a fairly common querey.

If you are unsure get an engineer to check it out for you.

Clyde 8)

[clyde]

Re: hotpoint dishwasher DWF50P ERROR codes

Dave 123 wrote:anybody help me with the error codes onthe DWF50P, it starts washing and halfway through stops with water still in. The eco and fast light flashes along with the rinse aid light. Ta Dave

Eco and fast flashing is a time out draining, check your filters and outlet plumbing. It may be a blocked pump. Get an engineer if you are unsure of your abilities – if you have a look yourself pull the plug out first :zap:

Clyde

[clyde]

kwatt wrote:More likely to be a module failure (as usual) on this though. 😉

K.

Wallet and large vodka time!!! £££££

[clyde]

Re: Zanussi jetsystem 1200 Help! Error E10! Help stop the be

Hi Flic

E10 is a fill problem, check the taps are turned on (and a definate water supply to machine) and there are no kinks in the fill hoses restricting the water. If they are ok it may be a faulty component in your washer.

Hope that helps

Clyde 8)

[clyde]

Re: Hotpoint WD420P

pxlee wrote:I need to replace the module on my Hotpoint WD420. Can someone tell me what is the exact Module No. – there seems to be so many. Also is it quite a simple job to fit myself or would I need to call in a specialist.

Whats wrong with the module??? and why are you trying to fix it yourself?
These appliances haven’t been out a year yet so it will be covered under your
first year parts and labour warranty. Call hotpoint out.

Clyde 8)

[clyde]

Re: Scandinova FF6745D …blowing hot air!

piecan wrote:Scandinova FF6745D Frost Free

if this means I have a dual compressor fridge freezer? .

Yeah it’ll be a twin compressor very common with scandinova.

Clyde 8)

[clyde]

Re: Proline TDV60 Thermostat problem

Part no for the thermostats is 1701896 email spares@ukwhitegoods.co.uk.
if you want a set.

Before you replace them check for blockages in the filter and vent hose and make sure it is venting out ok.

Pull the plug out before attempting any repair :zap:

Clyde 8)

[clyde]

Re: Creda Tumble Dryer – Problem

Martin wrote:

Jayb wrote:

.. ‘Cos you mentioned “Heater” and “Pump” which don’t relate to a UK produced product :con:

The new range of dryers have a lift pump in the bottom, water tank at the top

Clyde 8)

[clyde]

Re: Ariston AVD 149 fault code F-05

F 05 is a possible drain problem, check the filter located at the bottom behind the plinth. try and get as much water out the washer before you do this and have a couple of towels ready!

pull the plug out before attempting any repair :zap:

Clyde 8)

[clyde]

Re: Indesit dishwaster not draining

It’s probly going to be a blocked pump, or a blockage in you plumbing.
whats the model number? and do you get any flashing lights when its on?

If your plumbing is ok get an engineer out to do the repair – look in repairs@ for a local engineer

Clyde 8)

[clyde]

Re: Whirlpool AWZ650 BLOWING COLD

Hi Donny,

It’ll be the thermostats or the heater at fault. for a lasting fix change them both. If you remove the back panel then you will be able to access the parts.

If you are unsure of your abilities look in repairs@ for a local engineer, if you attempt the repair yourself pull the plug out first :zap:

Clyde 8)

[clyde]

Re: Shoes Off please

funkyboogy wrote:engineeer 1 pain in the RS customer 0

hope you didn’t drink her tea!!!

Seriously tho overshoes can be dangerous, i’ve heard of a cable tv installer slipping over on laminate flooring whilst wearing shoe covers and ending up on the sick! is it really worth the risk?

No shoes no repair – thats the way it should be.

Clyde 8)

[clyde]

Re: BRANDT WFH1671U BEARINGS

mbdas wrote: if I put some grease in them would it do any harm ❓

Grease the seal up – I’ve change a few blomberg bearing assy’s 55×5839, the bearing seals are lubricated with grease when supplied complete so you should be ok.

Clyde 8)

[clyde]

Re: One for the Comet guys…Proline FF959 Freezer

There are 2 pcb’s that were fitted during production, they are interchangeable but the wiring may need to be extended.

45×9781 has the terminals on the left side of the board and led’s on the right

45×8357 has both the terminals and the led’s on the right of the board

Hope that helps

Clyde 8)

[clyde]

Re: cheap oven

Try looking here;
http://householdappliances.kelkoo.co.uk … ngle-~pg-2

Clyde

[Author]

Posts