Forum Replies Created
-
Posts
-
Re: AEG Dishwasher pnc 911935627/03
when you say door pops open i assume you just close it and it satrts again
have you checked hinges to see if they have been strained
to check clse door slowly and about an inch before it latches does it go stiff and feel like it does not want close
dave
Re: Lamber/Newscan N5 350E Glasswaher
ring Chefquip 01299871856
they are the Lamber agent and may sent you info
Dave
Re: ILVE COOKER SPARES
2 options as far as i can see
1 i googled it and got http://www.ilve.com.au/
email company for british suppliers
2 if its 2kw or so you can get 1 madehave got a company on merseyside that does it and may do a postal service T P Fay 0151 546 6232
hope it helps
Dave
Re: LG wm12220fd
just change soap draw body common fault
can never see why it does it but changing body cures it
Dave
Re: Hotpoint WMA34p manual
if memory serves me when you select progs on this machine all the prog stage lights come on
if you select wash wash,rinse and spin are on
if you select rinse rinse and spin are ononly when you push start does all go out exept the stage you are in . at this point door locks and you away
what we need to know is what happens when you push start
Dave
Re: Relays. What is the difference between SPCO & SPDT?
to do that in a relay would require 2 coils or using a dc coil and reversing polarity
dave
Re: zanussi fridge freezer ZX99551
before you scap the board
check all capacitors for signs of the top bulging
try changing the power supply cap
from the picture i have connectors towards you look right hand side grey oblong block looks like a 1uf these go down with age
if it is that simple cheap fix
look in simple pcb repair tips above and you will see piture of other fridge boards with similar probs
hope it helps
DaveRe: Relays. What is the difference between SPCO & SPDT?
they are the same thing just a different way of describing
change over relay changes over from 1 contact to the other
therfore has 2 positions so double throw
same action as a 2 way switch
hope this makes it clearer
Dave
Re: Hotpoint AQXXF 149PI – no start
light goes to solid green when active
cant remember if it goes green before or after door lock
Dave
Re: Hotpoint AQXXF 149PI – no start
lid is difficult to come off you have to spring it at the back and push back at the same time waggle it up and down
wires to front panel go through top hinge
if you suspect panel send both pcb’s to emw they will test as pair
check both motor and heater for earth faults
Dave
Re: Viscount cooker model PC60GW
this looks lik an industrail cooker you need to try the big catering suppliers
you could ring a firm here on merseyside
Terry Fay 0150 546 6232 they make elements but i have got some industrail cooker spares off them
hope it helps
Dave
Re: AEG 60870 Error code 30
agree with seamy
fault 30 if i have correct model as there are 13 variants to this dishwasher
Water remains
in base trough
Leakage at recipient, discharge trough, hose system (e.g., Y-type hose), regeneration dosage
Inlet valve faulty
Water inlet too high (faulty flow governor at inlet valve)
Connecting hose regenerating dosing to discharge trough blocked
Water inlet channels in regeneration dosing unit blocked
Screens in the appliance clogged (also check spray arm nozzles for clogging)
Pressure controller faulty
Pressure controller hose obstructed, bent or leaking
Pressure controller wiring is faulty
Foam production in the appliance (splashed rinsing liquid / leaking dosing unit or con-compatible detergent / rinsing agent used)hope this helps
Dave
Re: Leisure Rangemaster 110 Gas, both ovens failed
you could check to see if the flame sensors have moved or gas burner blocked under sensor
apart from that sounds like a ffd fault
Dave
