[electrofix]

Re: WD420P Module

just to point out

if job is for a BANK hotpoint will see it as industrial so no guarentee watsoever if it went wrong the day after they bought it its tough

Dave

[electrofix]

Re: HOTPOINT WD61

would put a recon timer in better guarentee than secondhand if avail

ask EMW

Dave

[electrofix]

Re: Hotpoint WF740

souns like this fault

http://www.ukwhitegoods.co.uk/modules.p … ic&t=51155

yes prob pcb fault

Dave

[electrofix]

Re: Bosch WTL6307/05

looking in customer manual talink about water container and kinked outlet hoses may be a blockage somewhere

owners manual from here if this link works

https://portal.bsh-partner.com/TCcustom … chdb—wc3

hope this helps

Dave

[electrofix]

Re: WD420P Module

dont even think about a new board too much hassle

send board to EMW they will test and if faulty will repair

adv if you make a mistake and the board is not faulty it does not cost the earth

if you need number post and someone will tell you

Dave

[electrofix]

Re: SIMPLE PCB REPAIR TIPS

quite a few dishwashers use a 1uf or 1.5uf capacitor as a power supply for the pcb
when these go it is like having a low battery

fault you expect dishwasher turns on set prog
prog starts and dishwasher fills as soon as main motors switches on it all goes pear shaped (ie not enough power to hold in motor relay )

similar problem on the old hoover tumble dryers small pcb that start td
replace small cap (think its .22uf from memory) board repaired repair cost less than 50p

can supply part suppier info if reqd

Dave

[electrofix]

Re: hotpoint td ctd40g

thanks will ring them

Dave

[electrofix]

Re: Bendix Cooker CSI6001 Main Stat Mod Directions Prob?

only diag i have for this model shows a 4 tag timer

live
neutral

and two for switch contacts

from assumption any wire that goes to the timer from a stat will be picking up a live switch wire for the automatics this is wher i would look

you could check by installing stat get you meter between suspect wire and neutral main term. turn stat on and look at resistances if around 20 to 30 ohm will be ok

cna send you diag but may not help if you have a 6 tag timer

hope this helps

Dave

[electrofix]

Re: Hotpoint TDL 34P Static Shock

static shock are always a problem to pin down especially if the customer thinks its a 230v shock

dont normally get too many problems in winter

try using fabric conditioner its antistatic
nylon carpets can be a problem if you think this is it wet it with fabric conditioner and water mix in a hand spray that should sort it

Dave

[electrofix]

Re: bosch dryer fitting belt

agreed
easier from rear not a bad job when you work out the method you have to thread belt round fan and you can get belt through rear bearing after replacing rear bea use drum to pull belt on

hope this helps

Dave

[electrofix]

Re: Zanussi ZWF12080W

have no info on this machine too new but

1 if its that new send it back dont touch it why should you
2 if its thje same as the 12070 machine alarm codes are from the start pause button flashing red and green red fist digit green second digit of fault code door problems are e4* fault codes

hope this helps

Dave

[electrofix]

Re: Bosch ENR HBN430550b/02

all bosch diags and part breadown avail online

http://shop.bshappliancecare.com/

great service very useful

Dave

[electrofix]

Re: Hoover HNV 380 Tumble dryer. Quick!

sounds like an airflow problem

no air across elements therfore element overheats and trips stats

hope this helps

Dave

[electrofix]

Re: Proline H600W Cooker Hood Visor hinge brackets.

Proline is Comets own brand name contact their spares dept

Dave

[electrofix]

Re: Bosch WTE84107GB/02 Condensor Tumble Dryer

i remember going to an 18 series hotpoint and the customer had to tell me how to get into the front panel

was that long ago when hotpoint used a module and pmc to control the motor

we all have our bad day where we cant see the wood for the trees

Dave

[Author]

Posts