Forum Replies Created
-
Posts
-
Re: The old trade pump
Parts Center 160015977 Pump = £5.96
Qualtex Equiv (PMP62) similar price, or if you want the Askoll/Plaset ‘Bayonet Fitting’ less chamber, they are available from most pattern dealers at around a fiver! 🙂Re: WMA34 sump tank….
moon wrote:are there any in the east sussex area that wont cost an arm and a leg??
Try our Repairs@
Re: Neff Dishwasher S5456X2GB/42 Prog Selection Problems
laurenceuk wrote:Going to this machine tomorrow.
From the customers odd description of the symptoms I bet it’s just a case of needing ‘resetting’ to be honest 😉
From memory I think it’s the 2nd & 4th buttons held in for 3 seconds should solve it ❗
Re: Hoover HSW 110M Washer Dryer
The outer drum is made out of a synthetic polypropelene type material and could puncture if foreign bodies are caught between the drums.
So the first thing is the UNPLUG THE APPLIANCE :zap: in order to investigate further.
If you need help and a repairman? then click on this link:Repairs@
😀
Re: creda cooker 48905 over heating
williamh wrote:its just that i have been reparing cookers for about 5 years now and i have never come across that.
If you are ‘in the trade’ why not register as a Trade Member?
It’s totally free after all, nothing to lose and much much more to gain 😀
Re: Bosch T/Dryer WTA3100GB/02
Bryan,
I have yet to change a stat on one of these machines to be honest. I would tend to suspect the fan is the problem, either fluffed up or loose on the motor spindle. 💡
Don’t let that put you off ordering new stats, but as I say, I’ve never had problems with them (so far at least anyway 🙄 )
Re: Bosch WVF2000GB/34 washer/dryer drum bearing kit needed
Pete,
We can get you the bearing kit you need provided you add this information to your email as follows : Masterpart Kit No BS05109
http://shop.ukwhitegoods.co.uk/Washing+ … rings.html
and email that info to: spares@ukwhitegoods.co.uk who can order it for you.
As you have already discovered, Bosch do not supply a Bearing Kit at all for this machine, but we have other sources at far far cheaper prices to obtain the exact parts you need for the job 😉
Re: creda cooker 48905 over heating
All 4 regulators are wired in parallel so possibly one has failed shorting out the others 😕
For a local expert to check it out click on this link: Repairs@
Re: Whirlpool Condensor dryer AWZ650 overheating
Ian33,
In that case a little professional ‘TLC’ is called for (see link in my previous post) 🙂
Re: bosch dryer 3204gb
…by the way, because the fan only blows air in one direction only and thru the element box, during the short 3 second reverse tumble its not blowing and so the element switches off to prevent overheating !
Re: Indesit W12SUK
NTC in heater or Heater connections can lead you a merry dance if not fully checked :lesson:
Re: Whirlpool tumble dryer not heating
moorega wrote:There is even a resin encapsulated fuse on the incoming supply which is also OK.
In almost all cases the problem is that the element (Part No 481225928675) becomes open circuit. The 2 thermostats (Part No TOC36) that are attached are the second most usual failure.
The only other possibility is the exhaust stat (Part No 481227168369)
All can be obtained by emailing your requirements to: spares@ukwhitegoods.co.uk
:plug: POWER OFF AND UNPLUGGED BEFORE INVESTIGATING PLEASE :zap:
Re: Problem with Bosch – not taking in water
Garethh & DOBES are talking about the same sort of problem BUT 2 totally differing machines. 😕
So please let’s not get confused here.
i.e Symptoms = the same but the solution = very different :lesson:
