mbdas

Forum Replies Created

Viewing 15 posts - 166 through 180 (of 317 total)
1 2 3 … 11 12 13 … 20 21 22
  • Author
    Posts
  • September 20, 2006 at 7:23 pm in reply to: WHATS THE FASTEST WAY OF DEFROSTING A FROST FREE? #189119
    mbdas
    Participant

    Re: WHATS THE FASTEST WAY OF DEFROSTING A FROST FREE?

    Have used hair dryers before still can take 3/4hrs just to defrost it . I thought there may be a quicker way than that 🙁 Ive started using a hot air gun with a low heat setting but still takes 30 to 45 mins .
    what are the spray cans that defrost the ice like ❓

    August 16, 2006 at 6:00 pm in reply to: TDS offline disc #183159
    mbdas
    Participant

    Re: TDS offline disc

    Hi my TDS2006 has packed up so I thought i would order another but that part number for connections and masterpart now says NLA or obsulete 😥

    August 15, 2006 at 10:27 am in reply to: Masterpart web site #177691
    mbdas
    Participant

    Re: Masterpart web site

    NOP 🙁
    Cant even get on from the link on this page 😕

    August 15, 2006 at 8:13 am in reply to: Masterpart web site #177689
    mbdas
    Participant

    Re: Masterpart web site

    Hi 🙂
    Ive still not been able to get on masterparts web site and now I cant get on BDCs, they all cant be up dating at the same time ❓

    August 14, 2006 at 5:13 pm in reply to: KENWOOD D/W FAULT CODE #184889
    mbdas
    Participant

    Re: KENWOOD D/W FAULT CODE

    HI 🙂
    Its a KDW243A if that helps 🙂

    August 12, 2006 at 10:55 am in reply to: KENWOOD D/W FAULT CODE #184887
    mbdas
    Participant

    Re: KENWOOD D/W FAULT CODE

    Thanks Dave
    Ive not been to it yet and the ones Ive done in the past were Haier but this one is only a few weeks old so you never know 😕
    Thanks again 🙂

    August 11, 2006 at 11:51 am in reply to: DIPLOMAT DW ADP8242 #184836
    mbdas
    Participant

    Re: DIPLOMAT DW ADP8242

    Thanks dave
    but just spoke to the customer and its was fitted 2002 can you tell me the part number and do you know whats involved ❓

    thanks 🙂

    July 20, 2006 at 11:34 am in reply to: SAMSUNG Q1636SGS MOTOR ACTION #182165
    mbdas
    Participant

    Re: SAMSUNG Q1636SGS MOTOR ACTION

    Spot on guys 🙂
    Fitted module yesterday worked a treat 😀 😀
    Mark

    July 17, 2006 at 6:54 pm in reply to: SAMSUNG Q1636SGS MOTOR ACTION #182164
    mbdas
    Participant

    Re: SAMSUNG Q1636SGS MOTOR ACTION

    Thanks Guys I let you know what happens 🙂

    July 17, 2006 at 6:40 pm in reply to: SAMSUNG Q1636SGS MOTOR ACTION #182162
    mbdas
    Participant

    Re: SAMSUNG Q1636SGS MOTOR ACTION

    Hi 🙂
    Yes the motor does just judder one way and then aborts with E8 up
    I have continuity through the motor windings but not sure what the resistance values are ❓ I have 4.6k through the hall sensor thingy ❓

    July 11, 2006 at 9:01 pm in reply to: Hotpoint WD420 #181707
    mbdas
    Participant

    Re: Hotpoint WD420

    Hi 🙂
    check to see if the dryer is blowing air, there is a filter in the rear of the heater box on top
    mark

    July 11, 2006 at 8:56 pm in reply to: hoover wm dead #181629
    mbdas
    Participant

    Re: hoover wm dead

    Hi 🙂
    I’ve had one on a candy which had blown the 10k ❓ resister on the board caused by a short in the NTC
    mark

    July 11, 2006 at 7:44 pm in reply to: Whirlpool AWM8103 #181665
    mbdas
    Participant

    Re: Whirlpool AWM8103

    Hi 🙂 I went to one the other day customer had fitted a new door switch before calling me and that turned out to be just the carbons
    mark 🙂

    July 11, 2006 at 7:14 pm in reply to: Candy Fridge/Freezer CPCA291FFK #181674
    mbdas
    Participant

    Re: Candy Fridge/Freezer CPCA291FFK

    Hi 🙂
    You may or may not have mail ❓
    Mark

    June 8, 2006 at 6:32 pm in reply to: DAEWOO FRS2031iAL FRIGDE FREEZER #178637
    mbdas
    Participant

    Re: DAEWOO FRS2031iAL FRIGDE FREEZER

    OK 🙂
    An update the machine is doing nothing, front display is on and the compressor is not running and last night she unpluged it and then pluged it back in and now it seems ok 😕 this to me sounds like the module but which one ❓ any ideas
    Thanks Mark 🙂

  • Author
    Posts
Viewing 15 posts - 166 through 180 (of 317 total)
1 2 3 … 11 12 13 … 20 21 22