Seamy

Forum Replies Created

Viewing 15 posts - 1,786 through 1,800 (of 2,653 total)
  • Author
    Posts
  • in reply to: New World DW60 – not emptying after wash cycle #333341
    Seamy
    Participant

    Re: New World DW60 – not emptying after wash cycle

    Likely theres something fouling the pump impellor.

    in reply to: Tricity Bendix washing machine diagnostic #333110
    Seamy
    Participant

    Re: Tricity Bendix washing machine diagnostic

    When you say its not getting up to temperature do you mean its heating or not heating at all.
    If you feel competant to do so you might look at the heater first.
    If you don’t perhaps employing an engineer who can diagnose the problem may be best course of action to take.

    Fault codes & access to diagnostics are not available to the general public.

    in reply to: Miele Coffee machine #333272
    Seamy
    Participant

    Re: Miele Coffee machine

    F17 indicates insufficient water,
    F10 indicates no water dispensed

    possibly as simple as water tank not sitting correctly, or not filled to correct level

    in reply to: Electrolux on line part finder 404 error? #333332
    Seamy
    Participant

    Re: Electrolux on line part finder 404 error?

    http://shop.aeg.co.uk/node13.aspx

    in reply to: Zan ZWF16581W washer noise #333105
    Seamy
    Participant

    Re: Zan ZWF16581W washer noise

    Yes they fail, done a few under 1st year

    in reply to: electrolux 914602300-00 wd #333106
    Seamy
    Participant

    Re: electrolux 914602300-00 wd

    dryer heaters are known to cause all sorts of errors, check its not reading down to earth, disconnect all cables to dryer heater & see if problem is resolved

    in reply to: Zanussi ZWF12070W1 #332518
    Seamy
    Participant

    Re: Zanussi ZWF12070W1

    Hi Dave, the part you need is 1240349017 its a new type interlock that resolves the problem of doors with original type lock fitted intermittently staying locked.
    To clarify the earlier mentioned posting of mine, i thought that your appliance was covered by warranty still & couldn’t understand why you had’nt called manufacturers to repair it for free.
    Sorry for any offence caused. 😳

    in reply to: Beko WMA 667S – Concrete Block Problem #332664
    Seamy
    Participant

    Re: Beko WMA 667S – Concrete Block Problem

    Looks like you will be needing a weight too. Are you sure the bearings were done & that in fact it may have been the broken weight that was causing noise.

    in reply to: Beko no go #333012
    Seamy
    Participant

    Re: Beko no go

    Circulation pump motor seized most likely.

    in reply to: Belling 334wh Ser: 05 100547 11 #332896
    Seamy
    Participant

    Re: Belling 334wh Ser: 05 100547 11

    Shouldn’t require a wiring diagram really, most timers will have a neutral & live to power clock module, relay outputs (live) from timer goes to ovens.

    in reply to: Beko DE 2431 FW dishwasher #333076
    Seamy
    Participant

    Re: Beko DE 2431 FW dishwasher

    Float switches have been a problem & water counter also.

    in reply to: Zanussi ZWF14070 continuous pumping #332721
    Seamy
    Participant

    Re: Zanussi ZWF14070 continuous pumping

    Have found them to come back to life if you bring in water & empty them in service mode.
    Make sure you check pump/filter/hoses for blockages as machine always empties first before filling.
    If you provide an e-mail address perhaps someone will send you the necessary info’..
    😉

    in reply to: ZAN ZJD12191 Fills then stops #332409
    Seamy
    Participant

    Re: ZAN ZJD12191 Fills then stops

    E36 is not always the board, it most likely will be the DRYER HEATER 1242658308 ,, disconnect all dryer heater cables & tape up securely. Try on wash cycle, you’ll more than likely find theres no E36 then. 💡

    in reply to: AEG Favorit 5050 dw 911825059 fitting hinges. #332601
    Seamy
    Participant

    Re: AEG Favorit 5050 dw 911825059 fitting hinges.

    I think from memory it looks difficult but in practise is not too bad, think outer cabinet comes off as a complete unit. You only need to move it backwards a few inches to access the hinge mountings. Ages since i’ve done one though.

    in reply to: Electrolux F/Freezer Fridge Not Cooling #332533
    Seamy
    Participant

    Re: Electrolux F/Freezer Fridge Not Cooling

    Couple of things to check, that motorized flap is opening o.k & theres no blockage in duct from freezer to fridge, that fan is turning o.k, (i’ve had a few that turned o.k but were not as fast as they should be). Check door sw’ in freezer is working o.k also.

Viewing 15 posts - 1,786 through 1,800 (of 2,653 total)