Forum Replies Created
-
Posts
-
Re: zanussi tce7276w condensor dryer error code
Well to be honest only an engineer who looks at it can difinitively make a call on that. Without testing the appliance its impossible to tell for sure. But E50 is a motor related fault. A competant engineer should be able to diagnose further as to which area of the motor control is at fault. It could be something as simple as a cap’ failed, a blocked fan not allowing the motor to turn, seized drum or as serious as a motor or p.c.b.
Re: New Carbon brushes fitted how long would you ……
Motors are not dear for them anyhow, thats the good thing about Beko, motor about £40
Re: Zanussi TD4212W
Think theres a white plastic cap on it with 2 screws, it can be screwed off from inside drum if i remember correctly
Re: Zanussi ZWF12070W1 Door Will Not Open at End of Cycle
New type interlock needed, if its under guarantee i can’t understand why you are posting here, ring the manufacturers & have it repaired under warranty.
Re: Zanussi TD524 Felt bearing replacement
Not that easy really, theres a lot of stripping down to be done, power off of course.
Top off then both sides & back off.
Lift out drum, fit felt.
Rebuild & hopefully no screws left over.Re: Miele W842 Premier Novo – Excessive vibration
Turn drum with your hand when the doors open, if theres any roughness in the movement it may suggest bearing trouble. Bearings & suspension are not known to be that problematic to be honest unless it has gotten excessive use.
Re: Beko DRV5 62W tumble dryer staining laundry
It’s a sensor dryer, heater will be turned off in auto if no clothes in dryer or if not enough to make contact with sensor bars. Try timed drying for testing.
Re: **KNOWN ERROR CODES**
Chinese Zanussi ZWG1120,1140 etc (Little Swan)
E10 Fill overtime. No water level change in 3 minutes during filling the water. Check the water inlet valve, air pipe get broken or bad airproof. Check to have hung up the drain hose
E11 Lots of water in the tub. The water level is higher than the overflow water level when the washing machine at power on, delay, fault or running condition. Check the water inlet valve, the drain pump and the PC board
E12 Overflow The water level is higher than the overflow water level. The water inlet valve has failed.
E20 Bad connection of the drain pump. The PC board can not get the drain pump signal. Check the drain pump wire connection
E21 Drain overtime. The water level does not change in 3 minutes during drain. Check the drain pump.
Check the filter of the drain pump to prevent jam. Check the drain hose to prevent jamming.
E30 Can not lock the door lock. Fail to lock the door lock for 6 times when the PC board tries to lock the door lock after you press the START key. Check the door hook and the door lock to get correct location
E31 Can not unlock the door lock. Fail to unlock the door lock for 6 times Check the door lock
E33 Water level sensor fail. The frequency of the water level sensor is out of the spec. Check the water level sensor
E34 Temperature sensor fail. Temperature sensor (NTC) get broken. Check the temperature sensor (NTC)
E60 The motor can no drive. The motor fail to drive for 3 times. Check the PC board and the motor
E61 No speed feed back signal. The PC board can not get speed feed back signal when the motor drive. Check the speed feed back line of the motor to prevent fall off
E62 The speed feed back signal abnormality. Triac get brokenRe: Electrolux EWX1440W
Its likely its a EWF1440 model,
ED0 is the alarm shown to customer, but when you go into diagnostics you will see specific alarm, eg ED1 ED2 ED3 ED4 or ED6,ED1 = Data communication error between the WD board and PCB
ED2 = Drying heating element relay #1 faulty
ED3 = Drying heating element relay #2 faulty
ED4 = Relay which commutates power between the washing heating element and drying (in the WD board)
ED6 = No communication between PCB and display board (INPUT)As already stated many times on here the first thing to check is the dryer element down to earth as its 90{e5d1b7155a01ef1f3b9c9968eaba33524ee81600d00d4be2b4d93ac2e58cec2d} of the time causing the problem.
Re: Zanussi ZWF1220w Will not pump out when put through a pr
Filter or sump hose or pump blockage perhaps
